With the pressure meter located at Point B, the pressure of running water at point A is measured.Temperature 20°C and specific gravity of fluidsAccording to N/ m3; Ywater=9790 N/m?. \mercury =133100 N/m³. Yoil = 8720a) show The Co-print lines on the figure.b)if the pressure value in B is 87 kPa, calculate the pressure value at Point A.SAE 30 oilGage B6 стmercuryA5 cmiWater11 ст4 cm

Answered: Image /qna-images/answer/34b70c6a-70db-4765-82ed-f2bb2b9dffee.jpg

With the pressure meter located at Point B, the pressure of running water at point A is measured. Temperature 20°C and specific gravity of fluids According to N / m3; Ywater=9790 N/m² \mercury =133100 N/m³. Yoil = 8720 a) show The Co-print lines on the figure. b)if the pressure value in B is 87 kPa, calculate the pressure value at Point A. SAE 30 oil Gage B 6 cm mercury 5 cmi Water 11 ст 4 cm

With the pressure meter located at Point B, the pressure of running water at point A is measured. Temperature 20°C and specific gravity of fluids According to N / m3; Ywater=9790 N/m² \mercury =133100 N/m³. Yoil = 8720 a) show The Co-print lines on the figure. b)if the pressure value in B is 87 kPa, calculate the pressure value at Point A. SAE 30 oil Gage B 6 cm mercury 5 cmi Water 11 ст 4 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pressure gage B is to measure the pressure at point A in a water flow. If the pressure at B в is 87 kPa, estimate the pressure at A, in kPa. Assume all fluids are at 20°C. ywater =9790 N/m', Ymercury =133100 N/m2, yoil =8720 N/m³ SAE 30 oil Gage B Mercury 6 cm 5 cm Water flow 11 cm 4 cm
From the setup shown in the figure: If the manometer reads 60 mm, determine the gage pressure at B. If the pressure at B is 3.5 kPa, determine the manometer reading. Hg A Water Air 750 mm 200 mm 80 mm B Oil S=0.8
The gauge pressure reading at B is used to measure the pressure at point A in a water flow. If the pressure at B is 8 kPa, estimate the pressure at A in kPa. Assume the fluids are at 20 ° C. (Oil sg = 0.90, Hg sg = 13.6) Aceite SAE 30 B Mercurio- 6 cm 5 cm Flujo de agua 11 cm 4 cm
Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The friction factor of the pipe is 0.0225. The pipe slopes down at 10 degrees from the horizontal. Determine the difference in pressure between the start of the pipe to the end of the pipe. A) 287.79 KPa B 176.36 KPa c) 129.34 KPa D No Answer among the choices 238.86 KPa
Q2: Compute the value of (H) in centimeters such that the pressure at B is 90% of the pressure at point A. If the pressure at A is 79.4 kPa, S.G (oil)=0.89, S.G (mercury)=13.6. SAE 30 oil Gage B Mercury- 6 сm H Water flow 11 cm 4 cm
With the pressure meter located at Point B, the pressure of running water at point A is measured. Temperature 20°C and specific gravity of fluids According to N / m3; Ywater =9790 N/m³, Ymercury=133100 N/m³, Yoil =8720 N/m³ a) show The Co-print lines on the figure. b)if the pressure value in B is 87 kPa, calculate the pressure value at Point A. SAE 30 oil Gage B 6 ст mercury 5 cmi Water 11 ст 4 cm
Water flows through a pipe reducer shown in figure 2. The static pressure in the large diameter pipe and the small diameter pipe are measured by the inverted U-tube manometer containing oil of specific gravity less than one. Determine the manometer reading, thus show that h is given by the equation h = ng(1-SG) la SG Water Figure 2 The diameter of a pipe changes gradually from 75 mm at a point A, 6 m above datum, to 150 mm at B, 3 m above datum. The pressure at A is 103 kPa and the velocity of flow is 3.6 m/s. Neglecting losses, with the aid of a neat sketch, determine the pressure at B.
Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The friction factor of the pipe is 0.0225. The pipe slopes down at 10 degrees from the horizontal. Determine the difference in pressure between the start of the pipe to the end of the pipe. A) 287.79 KPa B) 176.36 KPa c) 129.34 KPa D No Answer among the choices E) 238.86 KPa
← Fluid Properties The diameter of droplet is 0.075 mm. What is the intensity of the pressure (N/sq. cm) developed in the droplet by surface tension of 0.000075 N/mm?
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
7) For the manometer setup shown, determine the difference in pressure between A and B. oll, s = 0.85 Water 680 mm Bo 1700 mm YWater 8) A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B. is h. 100 mm re A Mercury A B Oil, s = 0.90 %3!
At 20 degree celsius, gage A in the figure reads 295 kPa absolute. The tank is 2m wide perpendicular to the figure. Assume atmospheric pressure to be 1 bar. Sp.gr. of mercury is 13.6. Determine the total pressure acting on side CD in kN. P = 183 kPa abs. show solution and diagram