Why should PCM be preferable to DM for encoding analog signals that represent digital data?

Q: write the PSW format of 8051 microcontroller.

A: The question is on writing the PSW format or program status word format of 8051 microcontroller.

Q: Write a program in MIPS(MARS) to convert a binary digit (8bit) to a binary coded decimal (BCD).

A: Fundamentals of the Program: The registries are AL and BL. Transfer the data from 2000 to the AL…

Q: Explain the term coding gain. Under what conditions can the use of error correction coding make the…

A: Coding gain: It is the measure of difference between the signal to noise ratio levels between the…

Q: The distinction between multiplexing and demultiplexing may be summarized as follows:

A: A brief presentation on multiplexers: The multiplexer, abbreviated as "MUX" or "MPX," is a…

Q: Is it true that a digitizer is a piece of equipment that transforms analog data into digital form?…

A: Given: A hardware device known as a digitizer is one that can convert analogue information, such as…

Q: What is Packed BCD Format?

A:

Q: List and explain the motion compensation in video compression.

A: Motion compensation systems are designed to nullify the effects of heave or the effects of the…

Q: Write a program to quantize the sampled signal to a 4bit digital signal.

A: The question is to write MATLAB code for the given problem.

Q: In general, character devices are faster in transmitting data than block devices are. What do you…

A: Introduction: The characters are sent one at a time at random intervals. An excellent conversational…

Q: Design a 6-bit multiplier ?

A: Solution

Q: (2) In asynchronous transmission, why do we keep the number of data bits between the start bit and…

A: The start and stop bits are used in asynchronous communication as a means of timing or synchronizing…

Q: In general, character devices are faster in transmitting data than block devices are. What do you…

A: Storage devices known as block devices may read and write data operations in fixed-size blocks. Such…

Q: discrete Fourier transform in singal processing

A: the discrete fourier transform in signal processing is

Q: Using binary state encodings, complete a state transition table and output table for the FSM. Write…

A: Given equation about state machine.

Q: Suppose in the context of Binary Phase Shift Keying (BPSK), the binary data consists of 101 how…

A: Binary phase shift keying (BPSK) is a digital modulation scheme that transmits data by varying or…

Q: What is the name of the sum of rotational delay and seek time?

A: The Answer is in step2

Q: An analog signal is changed to a binary coded form by what circuit?

A: Analog to Digital Converter (ADC) is a circuit that is used to convert the analog signals such as…

Q: 02: Assemble the binary bits of the "PCM" signal below into a DPSK waveform, in the case of the…

A: I will explain it in details,

Q: hat are the differences between the CRC decoders for two separate cas

A: Introduction: СRС  is  а  different  аррrоасh  tо  reсоgnize  if  the  reсeived  frаme  соntаins…

Q: etermine the number of possible quantization levels if the number of bits per sample in a given PCM…

A: Quantization The process of quantization involves breaking down an analogue continuous signal into…

Q: The distinction between multiplexing and demultiplexing may be summarized as follows:

A: Multiplexing and demultiplexing are two concepts related to the transmission of data over…

Q: Arithmetic operations given below in 8-bit AVR microcontroller is carried out. According to this;…

A:

Q: Draw the architecture of 4 bit flash ADC with truth ta ble when reference in l Svolr

A:

Q: Design a block diagram of 8-bit flash ty'pe ADC by using two 4-bit flash types ADC. how can we…

A: An 8-bit flash type ADC is a type of analog-to-digital converter that can convert an analog input…

Q: 6. In CRC, if the generating function is 1001 1, and input bit stream is 0110001 101, what is the…

A: Cyclic Redundancy Check (CRC): It is an error detection method. It is based on binary division. CRC…

Q: Create a MIPS (MARS) software to translate an 8-bit binary digit into a binary-coded decimal (BCD).

A: Computer Basics Registers AL and BL are used. Move the 2000 data to the AL registry. From AL,…

Q: What is the difference between multiplexing and demultiplexing?

A: Introduction to multiplexers: The "MUX" or "MPX" stands for "multiplexer." It is a combinational…

Q: which assignments are corect with the following definitions? signal ABUS, B_BUS, Z BUS:…

A: Correct Option is : (d) BYTE(7 downto 4) <= A_BIT & B_BIT & A_BIT & B_BIT;

Q: difference between the si

A: given - In terms of the CE signal, what is the difference between the single-byte and burst modes?

Q: Give a brief rundown of at least three different techniques that are utilized to convert analog…

A: In order to represent and manage continuous signals in the real world, modern technology relies…

Q: Recall that the maximum input voltage for a 12-bit ADC on the TM4C is 3.3 V. If the input voltage on…

A: 1) We have 12 bit ADC 2) Max input voltage is 3.3V which generates 12-bit digital output of 0xFFF =…

Q: reate a MIPS (MARS) software to translate an 8-bit binary digit into a binary-coded decimal (BCD).

A: Program Basics Both AL and BL register. Transfer the 2000 data to register AL. Move values from the…

Q: Why should PCM be preferable to DM for encoding analog signals that represent digital data?

A:

Q: How does an adaptive mutex work?

A: Introduction: Every major data item only accessed by short code segments is protected by an adaptive…

Q: In general, character devices are faster in transmitting data than block devices are. What do you…

A: Character devices and block devices are the two primary categories of devices found in all Unix…

Q: A method for representing digital data analog signals by changing the phase of the analog carrier to…

A: Given that; A method for representing digital data analog signals by changing the phase of the…

Q: Explain the difference between multiplexing and demultiplexing.

A: Multiplexing is the process of sending a collection of signals and giving the output as only one…

Q: Design a datapath to solve the following equation: K is the input P=(1+ 102/128) K + 32 Define how…

A: To design a datapath to solve the given equation, we need to break it down into individual…

Q: Using binary state encodings, complete a state transition table and output table for the FSM. Write…

A: In a flip-flop, each state is stored. The binary encoding requires a lesser number of flip-flops.…