Who instructs change under NEC?

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: Find the centroid 200 mm 200 mm 400 mm

A: Hi there! since you have asked multiple questions, we will solve the first question for you. If you…

Q: Describe and explain, with annotated diagrams, four building components (either as part of the…

A: Daylighting design is provide enough daylight to an occupied space without any undesirable side…

Q: What is a multi-tube cyclone or multicone?

A: Air pollution is the addition of pollutants in the atmosphere which degrades the quality of air and…

Q: max = Amax=

A:

Q: What is the total length of extra bars at the midspan as shown below, 03.75 07.5 O8.5 O NONE OF THE…

A: length of extra bar at mid span  l=0.5L1 = 0.5×7.5l= 3.75m

Q: How hydrophilic self cleaning surface work？

A: Answer :- Water will spread entirely across the superhydrophilic surface, generating a very thin…

Q: Degree of external indeterminacy

A: Given data : Total number of support reaction =3+3+1=7

Q: السؤال الثاني what are the different between ?vertical and horizontal flow إجابتك

A: In case of horizontal floow the floow is from back to front

Q: Daylight is effective up to a depth about __ times the window height

A: Daylighting It is a process of brightening the room with the help of natural light through use of…

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Explain Dome and how many types of dome design in construction.

A: Answer:- Dome:- A dome is an architectural element similar to the hollow upper half of a sphere. A…

Q: P=51

A:

Q: Laminar flow?

A: flow in which plates of fluid slide over one another with relative motion due to viscosity is called…

Q: How are the redundant determined from the conditions of compatibility?

A: When the number of internal reactions in the structure is more than the number of equilibrium…

Q: What are the requirements for testing and adjusting instruments?

A: Testing and adjusting of an instrument is done to increase the efficiency  of test. Both Testing…

Q: What are the provisions in UBC-97 that NSCP did not fully adopt?

A: The National Structural Code of the Philippines (NSCP) and Uniform Building Code are the structural…

Q: What is Seismic Refraction?

A: Seismic refraction can be defined as it is a geophysical principle which is governed by Snell’s law.…

Q: the box. What is the probability ?that both marbles are red

A: Solution: Given that, No of yellow marbles = 3 No of red marbles = 2 No of green marbles = 4 No of…

Q: degree of indeterminacy.

A: Degree of Indeterminacy is of two types 1. Static indeterminacy  2. Kinematic Indeterminacy

Q: natural hazard emergency response

A: In any kind of natural hazard immediate relief and response is most required.

Q: Explain the designation W21 × 68

A: W21 x 68 is a type of Steel I beam. W refers to the Wide Flange beam. Thus, W21 x 68 is Steel Wide…

Q: Define the term diffusivity ?

A: The answer is below:

Q: What type of structure it is

A: It is frame based structure . This structure help to make the construction time less

Q: A steel tape is known to be 50 meters long at 10 C. If the coefficient of expansion is 1.16x10-5C,…

A:

Q: Transmissibility

A: Given data : For well at 20 m water is lowered (dw1)=2.11For well at 80 m water is lowered…

Q: 200 MPa 500 MPa 350 MPa

A:

Q: Define magma.

A: Magma is defined as the hot molten rock which is formed inside the crust level of the earth surface.…

Q: Define sensitivity

A: Define the sensitivity (St) :

Q: umber 1 locate the centroid of the shaded area.

A: \ Centroid for the section is About…

Q: What is the total distance between the centers of the first and last gasburners?

A:

Q: What are the specifications of Lovar tape?

A: Lovar tape: It is also know as surveyors tape in which it is made up of the alloy. It is not an…

Q: X A 90 mm ww 001 F 70 mm B

A: The ans is attached below:

Q: Draw a neat sketch and show IMPORTANCE OF CLIMATOLOGY IN ARCHITECTURE. Explain with reference of the…

A: The need for CLIMATOLOGY: Architecture is all about creating shelter from the natural world, and…

Q: x 6m deformed bars? t the correct response: 465 471 461 468

A:

Q: Why are there dead spots in some concert halls

A: Dead spots may occur in poorly built auditoriums. Dead zones are areas where two or more sound waves…

Q: The width of an outer aircraft panel is uniformly distributed between 1.00 to 1.10 millimeters.…

A: a) P(X > 1.05) = (1.10 - 1.05) / (1.10 - 1.00) = 0.5 Proportion of flanges that exceeds 1.05…

Q: In scientific terms, what is the identification of the water table or phreatic surface?

A: Phreatic surface is defined as the surface along which pressure is equal to atmospheric pressure. In…

Q: xplain

A:

Q: what is the impact of nonrecurring items?

A: Non-recurring items -  An abnormal or rare gain or loss in the company's financial statement is…

Q: Of the following statements below, which attributes regarding the interaction between the book and…

A:

Q: Explanation

A: Steel has good damping properties so not prone to vibration issues.  Creating curved sections of…

Q: How do I get RBA and RCA?

A: ASKED: To determine the reactions at B and C.   We will use the conditions of static equilibrium to…

Q: Which of the following most nearly gives the internal degree of indeterminacy?

A:

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.