While using the Buckingham pi theorem to obtain non-dimensional groups, the repeated variables are chosen to be density, length and velocity and the non-repeat variable is angualr velocity. What is the non dimensional group that will be found in the form of : Non dimensional group= angular velocity x density ______x length ______x velcoity __

While using the Buckingham pi theorem to obtain non-dimensional groups, the repeated variables are chosen to be density, length and velocity and the non-repeat variable is angualr velocity. What is the non dimensional group that will be found in the form of : Non dimensional group= angular velocity x density __x length x velcoity

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.18P: The drag on an airplane wing in flight is known to be a function of the density of air (), the...

See similar textbooks

Similar questions

The drag on an airplane wing in flight is known to be a function of the density of air (), the viscosity of air(), the free-stream velocity (U), a characteristic dimension of the wing (s), and the shear stress on the surface of the wing (s). Show that the dimensionless drag, sU2, can be expressed as a function of the Reynolds number, Us.
Given: The plane accelerates in its current trajectory with a= 100 m/s^2 Farag Angle theta= 5° W=105 kips F_drag= 80 kips m= 1000 lbs Find: F_thrust, F_lift Please include the KD. Fthrust Futel t Fueight 000 BY NC SA 2013 Michael Swanbom
The correct definition of Dimensional Analysis is: A procedure to find the yield point of a material when no definitive yield point can be determined graphically. A procedure to calculate the Elastic Modulus. A procedure to verify the size of a mass of material. A methodical process of converting from one set of units to another set of units. Match the following statements with the term that best describes each statement. (Enter Number ONLY) 1) Hooke’s Law 2) Creep 3) Impact Strength 4) Proportional Limit 5) Fatigue 6) Elastic The tendency of a solid material to move slowly or deform permanently under the influence of mechanical stresses below the yield strength of the material. The behavior of materials that deform when loaded but return to their original shape after the load is removed. The linear relationship between stress and strain in the elastic region below the proportional limit. The phenomenon where cracks propagate under loads…
What mathematical relationship exists between the wave speed and the density of the medium, using the POWER trendline equation from the graph? Make your response specific (i.e., describe the full mathematical proportionality between the two variables) Feel free to use the table. Table: Frequency (Hz) Density (kg/m) Tension (N) Speed (cm/s) Wavelength (cm) 0.85 0.1 4.0 632.5 744.12 0.85 0.7 4.0 239.0 281.18 0.85 1.3 4.0 175.4 206.35 0.85 1.9 4.0 145.1 170.70
b) The following shear stress – shear rate behavior was observed. Shear rate (Seconds-1) Shear Stress (dynes/cm?) 20 11 30 15.2 40 19.1 50 22.9 60 26.5 1. Make a plot of shear stress (ordinate) vs shear rate (abscissa) on log-log paper. 2. Can the fluid behavior be accurately modeled by the Newtonian, Bingham plastic, or Power law model?
Lab 2-Measurement Asynch - Tagged.pdf Page 4 of 7 ? Part I: Taking Measurements & Estimating Uncertainties for a single measurement www.stefanelli.eng.br The mass of the object is_ 0 i Parts on a tripie peam palance 0 0 10 20 30 1 100 2 3 40 200 4 +/- 50 60 70 5 300 7 400 80 Qv Search 8 90 9 500 100 9 10 g www.stefanelli.eng.br
These dimensions concern transportation systems. Look up the dimensions of the following vehicles; give the model year and the source of your information.a. A car of your choiceb. BMW 760 Lic. Honda Accordd. How wide is the driver’s seat in each car mentioned in (a) through (c)?e. A city busf. How wide are the bus seats?g. A high-speed passenger trainh. How wide are the train seats in the coach section?
a) Vortex shedding is a common fluid flow problem across bluff bodies. The design of buildings and bridges take into account the analysis of vortex shedding phenomena to avoid the occurrence of resonance, where the natural frequency of the body matches the vortex shedding frequency. In this analysis, the following parameters are found to be important: velocity of flow (V), density of fluid (p), hydraulic diameter of the duct (D₁), dynamic viscosity of fluid (u), width of body (B) and the vortex shedding frequency (n). Using the method of repeating variables, find the non-dimensional relationship governing the phenomena.
As we explained in earlier chapters, the air resistance to the motion of a vehicle is something important that engineers investigate. The drag force acting on a car is determined experimentally by placing the car in a wind tunnel. The air speed inside the tunnel is changed, and the drag force acting on the car is measured. For a given car, the experimental data generally is represented by a single coefficient that is called drag coefficient. It is defined by the following relationship: F, where air resistance for a car that has a listed C, = drag coefficient (unitless) measured drag force (N) drag coefficient of 0.4 and width of 190 cm and height of 145 cm. Vary the air speed in the range of 15 m/s
Ql: The viscosity in industrial measurement continue to use the CGS system of Lunits, since centimeters and grams vield convenient numbers for many fluids. The absolute viscosity () unit is the poise, I poise = 1 gtem. s). The kinematic viscosity (v) unit is the stohes, I stokes = 1 em /s. Water at 20C has u = 001 poise and also V= 0.01 stokes. Express these resalts in (a) SI and (h) BG tanits.
The velocity is usually density, gravity acceleration, diameter, height difference, viscosity and is a function of length. Using the method of repetitive variables and dimensionless required by taking density, gravitational acceleration, and diameter as repetitive variables find the parameters.
Thermal conductivity k is a measure of the ability of a material to conduct heat. For conduction heat transfer in the x-direction through a surface normal to the x-direction, Fourier’s law of heat conduction is expressed as: Q=-kA.dT/dx where ?̇ is the rate of heat transfer and A is the area normal to the direction of heat transfer. Determine the primary dimensions of thermal conductivity (k). Look up a value of k and verify that its SI units are consistent with your result. Write a set of primary SI units for k.