Which one of the following octave function is used to draw 2D discrete time signal. O supplot O plot O subplot stem

Q: Q8. Which of the following is possible value of crest factor for a non-liner load current? (ay 1.5…

A: Crest factor It is the ratio of peak value to the effective value of given signal

Q: Mask design. Silicon solar cell made of Al thin-film electrodes on silicon using lift-off…

A: According to the question, we need to draw a mask design for a silicon solar cell made of Al…

Q: Refer to the following figure, if VCE(sat) = 0.1 V, IC(sat) is equal to - 10 v 4.7 kn VIN Poc- 200…

A:

Q: 9. The amount of current that will operate an overcurrent protective device is inversely…

A: The over current protection (let us consider a fuse) operates on the heat development due to the…

Q: R, 2.2k R, 4.7k R, 470 R 470 15V R 1k R 4.7k Figure 2 Circuit 2 Schematic

A: The circuit can be redrawn as: So, the total resistance of the circuit is:

Q: How did 2 + j8ohms become 2 + 2 + j8ohms and then 8.9 ∠63.4? Like what did you do and why?

A:

Q: With aid of diagrams of MOS capacitor constructions, explain how positive voltage applied to VGS…

A:

Q: Solve for the following: V, Va, Is.Va,Vs.ls 12 ? 10! 10? 30 ? 200 80 2 24 V 16 ? V 40 60

A:

Q: A-) Explain with the help of diagrams the structure and operation of Hybrid (Magic) Tee

A: A tee in microwave use to connect a section of waveguide in series or parallel to the main…

Q: draw a diagram of electric power and energy system with all the basic components, and list the name…

A: Answer : to draw the electrical power and energy system

Q: Using a neatly and labeled drawn sketch, show the typical circuit arrangement of a monopolar…

A: It is asked to show the typical circuit arrangement of a Monopolar arrangement with ground return…

Q: Example 9.1 Incremental fuel costs in dollars per megawatthour for a plant consisting of two units…

A: Given: λ1=dF1dP1=0.0080P1+8 λ2=dF2dP2=0.0096P2+6.4 Loads:250 to 1250W Pmin=100MW Pmax=625MW

Q: Q2 |Find x plot t complex form of (Fs) for the function. -1 Scanned by TapScanner

A: Complex Fourier series:

Q: Problem 6. For the ckt below, determine: RTotal, 11, 12, and 13. 24 V 3 crms l1 из 12 8 ohms 18 ohms…

A: In this question, we need to determine the equivalent resistance, currents I1 , I2  and I3  . We…

Q: What is the required resolution of an instrument if the product characteristic specification is 10.0…

A: Resolution is the smallest change that the instrument can measure.  It is the least count…

Q: 9.3 A person is working on a steel structure while standing on the ground. An accident occurred…

A:

Q: 9. Draw and describe (stable/neutral/unstable) the type of system response one would expect from a…

A: We need to state the type of system response for the above diagrams.

Q: A2a R A26 Figure Q3a Figure Q3a shows the circuit schematic of part of an instrumentation amplifier.…

A:

Q: What does the term FACTS mean in the use of power electronics in Smart Networks using appropriate…

A: Flexible alternating current transmission systems (FACTS) is the system which is having static…

Q: The wind speed at 10m height is 5m/s, alfa value is 0.2, find the wind speed in both m/s and mph at…

A:

Q: In terms of Worst-Case Circuit Analysis, what formula should I use for finding VOUT in Worst Case?

A: For a linear circuit with resistors, we need to explain the formula used to determine VOUT in a…

Q: Determine the branch currents I₁, Igandl, in ampere. 50 1012 10 V al. The current in ampere 11…

A: We need to find out the current for given circuit by nodal analysis .

Q: 2-2 kn 10 RL =IK 4.7Km find InotoA and RooRton and V norten

A:

Q: Discuss causes of insulation failures in high voltage engineering. High voltage engineering

A: according to the question we have to discuss about the cause of insulation failures in high voltage…

Q: the course is power transmission system... Question : Differentiate between capacitance grading and…

A: Capacitance Grading Capacitance grading is done by employing various layers of different dielectrics…

Q: Assume a 20x25x4m hall. How many metersquare acoustic absorber surface do you need to decrease the…

A: The Reverberation Time (T60)  is given using Sabine’s Formula as shown below:…

Q: Voltage sags due to short circuit and earth faults are the cause for the vast majority of equipment…

A: Power Quality Problems Voltage sag Voltage swell Voltage spike Voltage fluctuation Harmonics Long…

Q: is the electrical voltage that generated from Thermo- Couple with c=3.75x10-2 and k=4.5x10-5 ,…

A:

Q: nse. Quèstion 8 NPN BJT is considered as two diodes their anodes are connected together. True False

A:

Q: be modekd byy The denie houm balow. acumentsoure com i para llelwith. a vesis don. when. a 100, f23…

A: The source is modelled as parallel combination of i and R. We will write equations in each case as…

Q: Variation of which of the following parameter is not consider as power quality problem for industry?…

A: We know that , the power quality parameters described are power, frequency, magnitude of the supply…

Q: Q14) Sketch the ouput Vout and label the levels. D1. Vout 1N3612GP 30Vrms 100HZ 0° R1 2kQ Vin .. ...…

A: In the given system, The Diode is 1N3612GP . The forward voltage drop of this Diode is 1 V. So,the…

Q: A1. (a) What is a nonlinear load? By illustrating the relationship between voltage and current,…

A: Voltage: The difference in electric potential between two places is known as voltage, often referred…

Q: Give examples of power ratings for home appliances and electronics.

A: Power Ratings:- The power rating of equipment in mechanical and electrical engineering refers to…

Q: Mention Factors determining the size and the direction of the generated emf

A: Factors determining the size and the direction of the generated emf are follows-

Q: The advantages of splitting vertically and horizontally varies. Describe them.

A: We need to tell about  advantages of splitting vertically and horizontally varies.

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.