Which one is the correct answer please?

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: Draw the following figure: 50000- 8.0000

A: The drawing of the given figure will be:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: Determine the forces in members CD, CJ, and DJ. M 11' A L 8' B L 6 panels at 6' K C L J D L I E L ↑…

A: To find force in member CD,CJ,DJ

Q: 5- HB Pencil is used to fill the sheet table. O True O False 2- Choose the correct answer: Oa- A3…

A: 5. HB pencils are used in a sheet because it gives dark mark to identify the sheet table so the…

Q: How did you determine to round up to 55 mm if the table never mention anything about 55 mm?

A: H=55 mm

Q: The correct choice is what

A:

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

A:

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: What is the module of a spur gear with 30 teeth and pitch diameter if 5 inches? 5.236 mm 4.233 mm…

A: The given values are -  Teeth T =30 Pitch diameter D = 5 inch(127 mm)

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: Question 1 The helical steel extension spring has a diameter of 2 inch, wire diameter of 0.1 inch,…

A: Given: diameter of the spring: D=2 inch diameter of the wire: d=0.1 inch for steel shear modulus:…

Q: 1500 liters/s of ammonia gas at 100°F and pressure of 30 in.Hg has a specific heat ratio of 1.304.…

A: Given data Q=1.5 m3/sT1=100°FT2=180°Fγ=1.304 Here, Q is the flow rate and T1 is the initial…

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Question 1 Johnny has recently purchased 110 acres of land in New Zealand. He has decided to grow…

A:

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: This is no answer sorry the answers are offered A B C or D

A:

Q: O I'd love ice-cream I love ice-cream

A: Correct is I love ice-cream.

Q: Please use different values. This answer you already gave me for a similar question. These values I…

A:

Q: A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected…

A: Given:m=70 kgθ=30°θ=40°Height AB=12mTo find:-1) Velocity VB2) The istance S

Q: Q34 gine exCumphe far nolineer operautor an

A: Given: To give an example of non-linear operator.

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: Only one of the following is correct. Select the correct answer. Continuous process production has…

A: Given: Multiple choice question

Q: If rods of these materials are the same size, select the lightest metal rod. Titanium Carbon…

A:

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

A:

Q: In a hot water heating

A:

Q: How do you solve parts a,b and c?

A:

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: se explain how you got the P1 and P2 final numbers from the giv

A: We have given in question T=200 and 250 degrees Celsius P=17.3 and 74.4 mm of Hg

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: 2. A composite furnace wall is made up of a 14 in. lining of magnetite refractory brick, a 5.3 in.…

A: Given data as per the question The thickness of brick =14 in The thickness of magnesia =5.3 in The…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.