Which of the following statement is NOT true? A To measure the current going through a component, the ammeter (DMM in current mode) should be connected in parallel with the component. B To measure the voltage across a component, the voltmeter (DMM in voltage mode) should be connected in parallel with the component. D To measure the current going through a component, the ammeter (DMM in current mode) should be connected in series with the component. All of the above.

Which of the following statement is NOT true? A To measure the current going through a component, the ammeter (DMM in current mode) should be connected in parallel with the component. B To measure the voltage across a component, the voltmeter (DMM in voltage mode) should be connected in parallel with the component. D To measure the current going through a component, the ammeter (DMM in current mode) should be connected in series with the component. All of the above.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.2: Telephone System

Problem 2R: At what height are the telephone outlets in this residence mounted? Give measurement to center....

See similar textbooks

Similar questions

17/ The charge across each capacitance when connected in a parallel connected capacitive circuit is ___________________. a. Same charges are observed across each capacitance b. Either same or different charges are observed across each capacitance c. None of the given option d. Different charges are observed across each capacitance
Please solve this question in electrical circuits
multirange ammeter was designed using direct method to give three scales with Rsh1= 0.001285989 0, Rsh2=0.000562552 0, and Rsh3=0.000100001 Q. The d'Arsonval meter has Rm=6 Q and full scale current of 1.5 mA. Find the ranges.? 8 (Ctrl) -
POWER SISTEMS high voltage technlque it is possible to measure pulsed (AND ANSWER THE SAME QUESTION FOR AC AND DC ) high voltages with the help of two spheres of equal radius placed on the same axis. In which case the approxlmate pulse voltage for pulse hlgh voltage , approxlmate voltage value for DC voltage , AND effective value for AC VOLTAGE voltage value that can be measured with such a system with diameters of 500 mm and known spacing between them is 2.5 cm, is given correctly. (Ambient conditions are neglected and take Ed = 30 kV / cm2 k = 0.9) a) 68,65114 kV b) 81.30081 kv c) 97,08737 kv d) 65,35947 kv e) 57.48835 kv f) 46.21612 kv PLEASE ANSWER THE THREE EQUESTION AND THE OPTIONS ARE THE SAME approxlmate pulse voltage for pulse hlgh voltage, approxlmate voltage value for DC voltage , AND effective value for AC VOLTAGE
Post Test Choose the letter of the correct answer. Write the chosen letter on a separate sheet of paper. 1. It is a smail component that lights up when current flows through it. a. Capacitor 2. It regulates the amount of current flowing in an electronic circuit. a. Capacitor 3. These are devices or components which do not require an external source to their operation. b. Fuse c. LED d. Resistor b IC c. Inductors d. Resistor c. passive devices d. electrical devices a. active devices b. electronic components 4. It is a three-terminal active component that is used mainly in boosting or amplifying electrical signals; both AF and RF ranges. a. Capacitor 5. it is necessary to turn the electrical circuit "on" or "off" a. Fuse 6. Testing tools that are capable of executing tests, reporting outcomes, and comparing results with earlier test runs a. Automated 7. The testing method that starts a soon as code is written and continues in successive stages as code is combined with other units of…
identify any equiptment at home that undergo an electromechanical energy conversion. name and discribe the function of each part involved in the conversion of the specific equiptment. with picture labeled
Fundamentals of electrical circuit
5. Determine RL voltage waveform for the circuit as shown in Figure 4.
1) Explain the functionality of the following circuit. Use text and waveform to explain.
That region is energy and potential
8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
TOPIC: Combination Circuits