Which of the following is true regarding a portable oloctrical power tool which is double insulated and hos a two-prong power cord plug?

Q: What is the voltage drop across RC, VC, in volts?  (Enter the number, not the units.)

A: Given circuit is -

Q: Derive current divider rule formula

A: The solution can be achieved as follows.

Q: List two examples and explain the reasons regarding to the behavior of power electronics device…

A: Based on their ON and OFF condition of the Power Electronics devices it can be categorizes in three…

Q: The -------parameters may not reflect the actual operating conditions but simply provide an…

A: 1. The advantages of the re model are that the variables are determined by the real operating…

Q: why UJT is good for reverse current blocking circuits?   Explain

A: Ujt is the unidirectional device .

Q: Draw the circuit of generated Pam??

A:

Q: 8. What is the primary difference between the BJT and the FET? a. current-controlled device and…

A: From the given options we need to determine the primary difference between the BJT and FET. BJT: BJT…

Q: Khee Voltage of Ilicon semi nductor. (without Your answer A condition where zero (0) volt is less…

A: 1) Knee voltage of silicon semiconductor is 0.7

Q: What will be the charge and mass of an electron? I am stuck. Please help. Will give good feedback.

A: Electrons are negatively charged particles and they revolve in elliptical orbits around the atomic…

Q: IGBTs have asymmetric voltage blocking capabilities is called ....... IGBT

A: Asymmetrical IGBT :-  => In this type of IGBT reverse breakdown voltage is less than forward…

Q: 4. Build an AND gate using transistors, switches and LEDs. Pressing the switch should emulate…

A:

Q: Power Electronics.   Write necessity of power supply and briefly describe different types of SMPS…

A: Power supply: It is an electronic device  that supplies electric energy to an electric loads the…

Q: Q.3 For Resistance temperature detectors (RTDS) I) What's the principle of operation for Resistance…

A:

Q: Hello, Not sure if this is possible but am i able to delete his answer from the system?

A: The solution is provided in the following section.

Q: ured value is not the same as the nominal value provided by the manufacturer? Measurement error due…

A:

Q: 3. (a) Discuss about the working principles of Light Emitting Diode (LED) with necessary figures.…

A: LED refers to light emitting diode, it is mainly used as it emits light when current flows through…

Q: Did you meet at the college .A a lot of .B anybody .C few .D

A: Given: Did you meet _______ at the college

Q: what does the NEC 420.6a state that the tables are not used for

A: NEC- It refers to National Electric Code in which the electric terms are coded with a specific code…

Q: The best sentence to describe dead band/time of the sensor is _____________________________. a. the…

A: Theere are certain  characteristic which defines how good theinstrument is these characteristic are…

Q: Assume you're the manufacturer of an FM radio receiver device. Write a user manual for your product.…

A: A radio receiver is an electrical equipment that is also known as a receiver, a wireless, or simply…

Q: Find the minimum size EMT raceway required to carry three (3) 500kcmil, three (3) 3/0AWG and two (2)…

A: When all conductors are the same size and have same insulation, NEC Table C.1 gives trade size base…

Q: Identify the error in which disturbance affecting the electrical circuit. O a. Approximation Error O…

A: Identify the error in which disturbance  affecting the electrical circuit. a. Approximation Error…

Q: IV) What is Cell Relay? Give applications.

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again. The…

Q: Identify and Explain with neat sketch of the 1. Pin Type Insulator 2. Suspension Type 3. Strain…

A: Pin type insulator: This type of the insulators the most early grown overhead insulator, yet are…

Q: Show a picture of t match and l match matching box. Which one would be better used for a PCB?

A: According to the question, we need to show a picture of T match and L match matching box. Also need…

Q: For an N channel E MOSFET what is the value of Id when VGS(TH)=3 V and Vgs(on)=4 V and k=1.5 mA/V2…

A:

Q: Explain the safest one to use in an aircraft GPS OR DGPS

A: Given: GPS or DGPS

Q: Punch Trough IGBTs have........... voltage blocking capabilities.

A: The IGBT is insulated-gate bipolar transistor. Based on structure the IGBT classified as, Punch…

Q: What are the different onboard sources of electrical power in a modern commercial passenger…

A:

Q: P-channel MOSFET is basically a following device. a. voltage operated O b. low-frequency operated O…

A: MOSFET is controlled by the application of GATE pulse .  GATE pulse controls the conduction state of…

Q: Could you please go into more detail about how the Ac equivilant model was created? thank you

A: The AC equivalent model of the circuit need to be explained for the given volt

Q: Explain and draw an NPN transistor chip in a circuit of your own design. I want the actual chips…

A: An NPN transistor has three terminals: the emitter (E), the base (B), and the collector (C). In an…

Q: What are the risks associated with NOT implementing ISO 27001 in an organization ? What are some…

A: ISO 27001: It provides a standard framework to manage information and data for a modern…

Q: 5. (a) What is the full form of the word "LASER"? Explain how stimulated emission amplifies light in…

A: (a) LASER: The full form of LASER is "light amplification by stimulated emission of radiation". A…

Q: How the trailing current in IGBT is different from the MOSFET?

A: Trailing current is a phenomenon that occurs in both IGBTs (Insulated Gate Bipolar Transistors) and…

Q: project using 555 timer, photoresistor, and LED. show a product design using this items

A: Photo Resistor is a component which is used in the circuit which works on the principle of…

Q: the pathway of a cell phone signal from the caller to the receiver

A: In this Question It is Asked to Trace the pathway of a cell phone signal from the caller to the…

Q: When the pinch-off voltage is exceeded, ID will ____ as VDD increases.   a. double   b.…

A:

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.