Which of the following is the rating life for a ball bearing with total expected life of 20 x 106 revolutions at 99% reliability? Group of answer choices 37 x 10^6 rev 79 x 10^6 rev 2.7 x 10^6 rev 149 x 10^6 rev

Q: A. Which parameters are used for passage from real multi-axial stress condition to one-axial…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is the resulting Soderberg's factor of safety of a 1.82" diameter shaft operating under the…

A: Given:Diameter of the shaft, d=1.82 inMean torque, Tm=14.9 kip.inAlternating torque, Ta=3.6…

Q: An electric motor sleeve bearing is intended to be used for an agricultural machinery using a medium…

A:

Q: It has a full-slide type bearing rotating at a speed of 1975 rpm. A load of 5693 N is applied. SAE…

A: Disclaimer: "Since you have posted a question with multiple sub-parts ,we will solve first three…

Q: he diameters of shafts with a nominal size of dn = 68 mm must be within limits dmax = 68.045 mm and…

A: Given:dmax=68.045 mmdmin=60.015 mmdn=68 mm

Q: 10 units of bulb were tested where the normal lifespan is 100 hours 3 units of bulb failed at 10…

A: Failure rate per hr.

Q: A deep groove ball bearing is subjected to a equivalent dynamic load 7240 N. If the rating life is…

A:

Q: True or False a) If an accurate value for the notch sensitivity is hard to find, I should consider…

A: 1.If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue…

Q: A taper roller bearing used in the automobile industry has a radial load of 2978 N and an axial load…

A: Given data: Fr=2978 NFa=1220 NX=Y=1 Need to determine the value of the equivalent dynamic load.

Q: A workshop technician used an Ingersoll Rand impact wrench to tighten and loosen tyre nut for an…

A: Given : ax = 3 m/s2 ay = 7 m/s2 az = 5 m/s2. To find : Total vibration value

Q: 15.)A full journal bearing has a journal diameter of 4.000in. with a unilateral tolerance of…

A: Journal bearing: The main function of the bearing is to avoid direct metal-to-metal contact while…

Q: How long is the thread at 4B?  What do the brackets around dimension 241 at 3C indicate?

A: It is asked to find the length of thread in section 4B and also the meaning of parenthesis in…

Q: A full journal bearing has a journal diameter of 37 mm, with a unilateral tolerance of -0.012 mm.…

A:

Q: 8) The main failure mode of worm drive is A. Fatigue pitting of tooth surface C. The bonding and…

A: Gear drive is used to transmit or reduce the transmission ratio. A worm drive is the most effective…

Q: What minimum dynamic load rating is required for a deep groove bearing that is required to have a…

A: Given:The life of the bearing at  reliability, The equivalent radial load,

Q: The table gives data concerning the shrink fit of two cylinders of differing materials and…

A:

Q: 3 mm along the rod from end C. Assume that F = 660 N. What is the component of F that is…

A: Given data  F = 660 N Find the force along and perpendicular to the AC.

Q: (RIV) 43 axial load (kN) греed (rpm) ne static and dynamic load capacities of the Eng are 50 and 68…

A:

Q: The length of stroke of a four cylinder four stroke cycle SI engine is 1.6 times the diameter of the…

A: Given L= 1.6 D Brake power = 25 kW N= 2450 Mechanical efficiency = 85% Mean effective pressure = 8.5…

Q: Assume that the life of a roller bearing follows a Weibull distribution with parameters 3 = 2.3 and…

A:

Q: 6-4

A: Step 1:Solutions :To figure out which forklift to suggest utilizing the IRR strategy, we really want…

Q: Machine Design

A: Ry = 183.1 lbfRz = -861.5 lbf Speed =1200 rev/min Life-time = 15 kh = 15000 h Reliability, RD = 95%…

Q: 1.1. Journal bearings are one of the most common types of hydrodynamic bearings. Their primary…

A:

Q: explain the Factor of Safety ? include minimum and the max

A: Explain the Factor of Safety, which include the minimum and the maximum FOS.

Q: Please Full Answer A) 1) Explain two Types of bearing 2) Explain about Absolute viscosity, kinematic…

A: Answer: (1) TWO DIFFERENT KINDS OF BEARINGS a. BALL BEARING: These components can resist both…

Q: An engine system of 3 msin components in a series sll having the same reliability. Determine the…

A: Given   Three main components. Reliability of the system = R1 = R2 = R3 0.995 Find    Level of…

Q: A journal bearing has the following characteristics: dshaft = 75 mm dbushing =75.05 mm operating…

A: Given data  diameter of shaft/journal (d) = 75 mm  diameter of bushing/bearing (db) = 75.05 mm  N =…

Q: A suitable factor of safety to apply when selecting the cable for a factory hoist is: 05 O1.2 0.2…

A: Since you have posted multiple questions, we will provide the solutiononly to the first question as…

Q: Angular contact ball bearing and tapered roller bearing are often used in pairs on a shaft in…

A: Given: Angular contact ball bearing and tapered roller bearing To define why these type bearing…

Q: Question 8 Which of the following pressure losses contributes to Equivalent Circulating Dens-…

A: Que.8  The following pressure losses contributes to Equivalent Circulation Density bottom: Correct…

Q: According to the textbook, CH 5, what is a generally acceptable design factor for drive axle under…

A: Design Factor:A design factor, also known as a safety factor or factor of safety, is a numerical…

Q: A ball bearing, rotating at 1200 revolutions per minute, operates at a radial equivalent load of 29%…

A: Given:The revolutions of bearing, The radial equivalent load is  of its dynamic load rating.

Q: A self-aligning ball bearing is to be selected to carry a radial load of 5 kN and a thrust load of 2…

A:

Q: What tolerance class is specified for the thread? h class?

A: Let us discuss above engineering drawing for tolerance class.

Q: A steel shaft is to be designed so that it is supported by roller bearings. The basic geometry is…

A:

Q: A roller bearing is subjected to an equivalent dynamic load of 1200 N. If the rating life is 25 x…

A: