Which of the following is not a characteristic ofparallel circuits?a. Total circuit resistance is always less thanthe resistance of the leg with the lowest totalresistance.b. The current through each leg will be differentif the resistance values are different.c. The sum of the resistance in each leg equalsthe total circuit resistance.d. Source voltage will be dropped across eachleg of the parallel circuit.

Q: is available in the electric systems and mechanical systems. O liquid air O gas no medium

A: Mechanical system: A set of components which convert a specific input force or motion into a desired…

Q: Which of the following is an example of electronic technology? The xbox Windshield wipers Legs of a…

A:

Q: What are the specific applications of the Solenoid actuators in Mechatronics systems.

A: following is the answer to the above question -

Q: Which of the following is the best example of an underdamped system? O A) A car door that once…

A: Under damped system: The condition of the system in which oscillations of a system returns to…

Q: Label the various pneumatic components of the circuit below

A: In this problem, it is saying to label various pneumatic components of the circuit.

Q: What are the control methods for electromechanical systems. What are the advantages of each method?

A:

Q: In which control system, output from the system has no effect on command signal? O a. Feedback less…

A: In Feedback less system, output from the system does not sent back to the controller. Therefore,…

Q: give 3 examples of automatic control systems using the open loop idea.

A: A Control System which doesn’t have any feedback connected to it is called as Open Loop System.…

Q: Question / hand-held torch uses two 1.5-V batteries which together supply 4.7 kJ steadily to the…

A: Given data:

Q: What is the difference between Momentary Contact and Maintained Contact?

A: Maintained Contact means that when you push it on it stays on until you push it off and so on.

Q: .a. What is the purpose of thermostat number 2, IN7, in the mixing vat machine

A: To maintain the proper temperature, a thermostat regulates the flow of a heat transfer fluid or…

Q: Define sensors and list the various specifications that need to be carefully studied before using a…

A: Sensors basically used for the measurement of various quantities such as pressure, tempertature etc.…

Q: Differentiate the alarm designs for chemical plants and offshore oil platforms.

A: Difference in alarm system of chemical and offshore plateformsare:1.Alarm system of chemical plants…

Q: Which of the following is the best example of engineering control? A. noise-cancelling headphones

A:

Q: 02/Explain the operation and benefits of AMT.

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: When n-type material is sandwiched between two p-type materials such type of transistor is called:

A: Solution: When N-Type material is sandwiched between two P-Type materials, Such a Type of Transistor…

Q: Which of the following is an example of digital transducer ? a. LVDT O b. Encoder O c. Thermistor O…

A: A digital transducer is a measuring device that produces a digital output. Any transducer that…

Q: All terminals have a defined wire size range. If I had a wire of 2.0mm / 15 AWG, what terminal…

A: Calculate the cross-sectional area of the wire by using the 15 AWG. 15 AWG=1.65 mm2

Q: What happens when the low-voltage current flow inthe coil primary winding is interrupted by the…

A: Primary winding and scendary windings aare used to increases or decreases the current and voltage…

Q: Schematics are always drawn to show components in their de-energized or off state.

A: Schematics is an electrical or electronic circuit diagram.

Q: Explain Automatic Door Open Close System PLC Ladder

A: Door Open Close System PLC Ladder If a person comes into the field of an infrared sensor, the motor…

Q: Compare any two speed control circuits with neat circuit diagram. (Meter in, out or bleed off)

A:

Q: What happens to an electrical circuit when thereis unwanted resistance in it?

A: Given Data : Electric circuit

Q: short objecytive of pneumatic circuits

A: Answer- A pneumatic circuit is an interconnected set of  components that converts compressed gas…

Q: In order to read the voltage generated from a Thermocouple, Select one: a. It should be connected to…

A: Thermocouple generate a temperature dependent voltage, that voltage signals are amplified by the…

Q: What is the main difference between an electrical and mechanical power?

A: Difference between electrical and mechanical power.

Q: Choose two which are NOT benefits of Automation Systems   Reduce Energy Consumptions   Reduce…

A:

Q: List the three modes of industrial process control and specify the effect of each when a process…

A: In any industrial plant, various types of operations proceed. A process is the conversion of raw…

Q: Upon knowing the different types of the Airconditioning system, which system do y think is the best…

A: a. Types of air conditioning in hospital HVAC designer (using HEPA filter) will recommended in…

Q: 12. A short circuit is placed across the leads of a resistor, the current in the resistor itself…

A: Given A short circuit is placed across the leads of a resistor the current in the resistor itself…

Q: What is the following systems, , where do they used, what is the specefication of such systems, what…

A: The engine is made composed of a stationary cylinder and a moving piston. As the gas expands in…

Q: hile discussing NTC thermistors; Technician A says that some systems use this type of thermistor as…

A:

Q: The Electric hand dryer is an example of........ loop system

A:

Q: 10. A diode under forward biasing acts like (a) an open switch (b) a closed switch

A: At whatever point an indicated voltage is exceeded, the diode resistance gets expanded, making…

Q: Which of the following is a control that relates directly to vacuum controlled EGR systems??…

A: PORTED VACCUM SWITCH IS A CONTROL THAT relates directly to vacuum controlled EGR systems as No…

Q: Which is the correct path of information through a control loop

A:

Q: How many degrees are the current and voltage out of phase witheach other in a pure resistive…

A: The power varies between positive and negative instantaneous values over time, as it does in…

Q: Why is a low-voltage thermostat normally more accuratethan a high-voltage thermostat?

A: The low and high voltage thermostat are the direct wired heaters. The low voltage thermostat is…

Q: 13) Which of the following is NOT process control? A: Temperature control B: Lighting on/off control…

A: In process control, process variable (such as temperature, pressure etc.) is measured (using…

Q: What are the types for pressure-releasing circuits? Please explain their differences.

A: The Pressure releasing circuits uses pressure control valves for keeping the system pressure below a…

Q: What is the voltage at node 2 in the circuit

A:

Q: Parallel circuits are used in the airconditioning industry to __________.a. supply the correct line…

A: Most loads use line voltage as their power source. The parallel circuit allows the line voltage to…

Trace the circuit

In any specific circuit, the elements included are transistors, resistors, diodes, capacitors, and many others. All the elements are associated with wires, and the current is used to travel from these wires. Generally, at least one active component must be present to be known as electronic rather than electrical. The mixture of elements as well as conducting wires gives several types of processes to be executed, which are amplifying the signal, computations, and transporting data from one place to another.