Which of the following increases the rotational inertia of a solid diet about its axis, without changing its mass? Drill holes at points near the rim and put the material at points between the holes O Drill holes at points near the axis and put the material at points between the holes O Drill holes near the rim and put the material near the axis O Drill holes near the axis and put the material near the rim O Do none of the above (the rotational inertia cannot be changes without changing the mass)

Which of the following increases the rotational inertia of a solid diet about its axis, without changing its mass? Drill holes at points near the rim and put the material at points between the holes O Drill holes at points near the axis and put the material at points between the holes O Drill holes near the rim and put the material near the axis O Drill holes near the axis and put the material near the rim O Do none of the above (the rotational inertia cannot be changes without changing the mass)

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 54P: A cylinder with rotational inertia I1=2.0kgm2 rotates clockwise about a vertical axis through its...

See similar textbooks

Similar questions

An automobile engine can produce 200Nm of torque. Calculate the angular acceleration produced if 95.0 of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0-kg disk that has a 0.180-m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
Today, waterwheels are not often used to grind food. Instead, we have electrical devices such as blenders, choppers, and mixers. The electric motors in these devices are similar to a waterwheel, but instead of falling water causing the wheel to spin,electricity causes a shaft to spin. The specifications on a particular electric motor reports that at 1.75 103 rpm, it puts out5 hp. What is the corresponding torque in N m?
A potters wheela thick stone disk of radius 0.500 in and mass 100 kgis freely rotating at 50.0 rev/min. The potter can stop the wheel in 6.00 s by pressing a wet rag against the rim and exerting a radially inward force of 70.0 N. Find the effective coefficient of kinetic friction between wheel and rag.
Calculate the rotational kinetic energy of a 12-kg motorcycle wheel if its angular velocity is 120 rad/s and its inner radius is 0.280 m and outer radius 0.330 m.
A student rides his bicycle at a constant speed of 3.00 m/s along a straight, level road. If the bikes tires each have a radius of 0.350 m, (a) what is the tires angular speed? (See Section 7.3.) (b) What is the net torque on each tire? (See Section 8.5.)
A competitive diver leaves the diving board and falls toward the water with her body straight and rotating slowly. She pulls her arms and legs into a tight tuck position. What happens to her rotational kinetic energy? (a) It increases. (b) It decreases. (c) It stays the same. (d) It is impossible to determine.
The blades of a wind turbine are 30 m in length and rotate at a maximum rotation rate of 20 rev/min. (a) If the blades are 6000 kg each and the rotor assembly has three blades, calculate the angular momentum of the turbine at this rotation rate. (b) What Is the torque require to rotate the blades up to the maximum rotation rate in 5 minutes?
Consider an object on a rotating disk a distance r from its center, held in place on the disk by static friction. Which of the following statements is not true concerning this object? (a) If the angular speed is constant, the object must have constant tangential speed. (b) If the angular speed is constant, the object is not accelerated. (c) The object has a tangential acceleration only if the disk has an angular acceleration. (d) If the disk has an angular acceleration, the object has both a centripetal acceleration and a tangential acceleration. (e) The object always has a centripetal acceleration except when the angular speed is zero.
Two spheres, one hollow and one solid, are rotating with the same angular speed around an axis through their centers. Both spheres have the same mass and radius. Which sphere, if either, has the higher rotational kinetic energy? (a) The hollow I sphere, (b) The solid sphere, (c) They have the same kinetic energy.
A force of F=(2.00i+3.00j) N is applied to an object that is pivoted about a fixed axle aligned along the z coordinate axis. The force is applied at the point r=(4.00i+5.00j)m. Find (a) the magnitude of the net torque about the z axis and (b) the direction of the torque vector .
Repeat Example 10.15 in which the stick is free to have translational motion as well as rotational motion.
A cylinder with rotational inertia I1=2.0kgm2 rotates clockwise about a vertical axis through its center with angular speed 1=5.0rad/s . A second cylinder with rotational inertia I2=1.0kgm2 rotates counterclockwise about the same axis with angular speed 2=8.0rad/s . If the cylinders couple so they have the same rotational axis what is the angular speed of the combination? What percentage of the original kinetic energy is lost to friction?