Which is not a valid safety class? a. CAT II b. CAT III c. CAT IV d. CAT V

Q: Type UF cable shall not be used where subject to physical damage. A. True B. False

A: Generated power needs to be distributed to different loads. Cables are used for transferring power…

Q: Identify a real life device/control system application configured as Open-loop Control System and…

A:

Q: The Voltage between the contacts during the arcing period is Land is just sufficient to_ O a. Very…

A: Vacuum circuit breaker.  Vacuum circuit breaker has minimum gap between fix and moving contact.

Q: Which jacks should be used and what setting should be chosen on the selector switch to measure…

A: Multi meter can able to measure various quantities such as current, voltage and resistance. It also…

Q: g Technology- Toronto CHAPTER 7: SOLDERING TECHNIOUES ES 7.5 QUESTIONS Which tools will you need for…

A: Note: According to bartleby guidelines, we have to answer only first question. 1) Soldering is the…

Q: Draw a simple block diagram of 'Open-Loop Control System' and 'Closed-Loop Control System' Not…

A: CS - control system

Q: Does NEC provides maximum guidelines or minimum guidelines

A: The solution has been provided in the following section:

Q: What is the most important rule of electrical safety?

A: In this question we will write most important rule of electrical safety...

Q: Draw a simple block diagram of 'Open-Loop Control System' and 'Closed-Loop Control System' Not…

A: Note -  CS - control system

Q: What is a starte

A: A motor is an electromechanical device which is used to convert the electrical power into mechanical…

Q: Short answer. Explain meter loading and why it is important to consider.

A: Meter Loading  Meter loading is generally seen in electrical devices used to measure the voltage and…

Q: Auxillary carry flag will be set whenever а. there is a carry from lower nibble to higher nibble as…

A: Choose the correct option Auxiliary carry flag will be set if?  8085 microprocessor is 8 bit…

Q: Prepare the specific requirements which ought to taken into consideration when developing an…

A: The protection system is a very vital part of the power system because the reliability of the power…

Q: Identify the system which has low stability. a. None of the above b. Open loop and Closed loop…

A: Consider the open loop control system: In this the control system depends only on the input and is…

Q: Explain and why 20 words, Advantages of Electrical Method for each number. Advantages of Electrical…

A: 1. When compared to the other methods, the electrical method is more effective and takes less time.…

Q: Fiber cable sheath is removed by a. Wire Stripper b. Jacket Stripper c. Miller Stripper d. Round…

A: The solution is given  Answer is option b

Q: consists of tooth and slot. O a. Brush b. commutator O C. Yoke d. Armature

A: Tooth and slot are used to hold the winding. So we will eliminate options by considering each.

Q: Please explain whether NEC provides maximum standards or minimum standards?

A: NEC stands for National Electrical Code.  It provides some basic sets of standards that must be…

Q: 7.b. Which of the following is not a brand name of a high-pressure sodium lamp? A. Multi Vapor. B.…

A:

Q: what is nuisance tripping?

A: Nuisance tripping is the repetitive tripping of the RCD in absence of any serious hazard. The…

Q: 5. Define fuse coordination. Why it is important in electrical power systems?

A: fuse coordination is the type of coordination which study about fuse and circuit breaker…

Q: . A maintained push button will A. hold its position after it is pressed and released. B. open after…

A:

Q: Lockout is required: During servicing and maintenance where unexpected ener- gization or start-up of…

A: Bartleby has policy to solve only first question and if it has subparts then solve only first 3…

Q: Explain the essential features of Indicating Instruments Explain the significance of Fluid friction…

A: Indicating Instruments Indicting instruments indicate the magnitude of an electrical quantity at the…

Q: Choose the correction action to respond immediately in the event of an accident or any other…

A: Given, The correction action to respond immediately in the event of an accident or any other…

Q: Explain mounting arrangement and positioning of switch boards

A: Switchboards are electrical panels that are used to control and distribute power in buildings or…

Q: Airframe Electrical What are the three connector contact densities?

A: Electrical connector is a device which is used to connect conductors of different wires. Electrical…

Q: With suitable illustrations explain the principle of operation and working of Moving Iron…

A: Moving iron instruments In moving iron instruments, deflecting torque is proportional to the square…

Q: In what ways may the Instrusion detection and prevention system be used to reduce the hazards of…

A: Intrusion detection and prevention system is used as no one can enter our system with malicious…

Q: Define and differentiate accidents, unsafe acts and unsafe conditions. essay at least 30 words

A: Electrical Hazards: Hazards are always there with Electricity. it causes damage to equipment on…

Q: 4.-What is switch bounce? Describe two techniques to minimize switch bounce.

A: Brief Concept- Switch bounce- The brief separation of contacts that occurs when a mechanical switch…

Q: Explain in detail what ring counters are and how they are employed.

A: given  we need to give a detailed explanation about ring counters and their applications

Q: 18. What are the types of fuses in common use?

A: Fuses in common use

Q: What is electrical earthing ans its type?

A: Electrical Earthing: It is the phenomenon of discharging the electrical energy immediately into the…

Q: Conductors of dissimilar metals shall not be intermixed in a terminal or splicing connector. Please…

A: The guideline of not intermixing conductors of dissimilar metals in a terminal or splicing connector…