Which controller has high gain ? O a. Proportional derivative O b. Integral O c. Proportional O d. Derivative

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: What is the weight of 3 slug, expressed in pounds-force? 96.522 lbf

A:

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing…

A: According to the given data Horizontal distance between A and B =18 Vertical Distance between A and…

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: 3.00- 1.25-

A:

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: 2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50…

A: Least count of Vernier caliper = 0.02 mm

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: of bell wire in inventory is to be approximated by weight. The weight of the wire is listed in the…

A: Weight of full spool = 2038=1638 ouncesEmpty Spool weight = 114 = 108 ounces

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is second.

Q: Write dimensions of work and please explain neately.

A: Given Data⇒ Work

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

A:

Q: In a turning operation on carbon steel with hardness- 175 HB. the cutting speed - 225 m/min, feed-…

A: GivenV=225m/minf=0.25mm/revd=7.5mmη=90% Cutting energy for Brinell hardess 175Hb=1.6J/mm3U=1.6J/mm3

Q: In a forming process the length of material changes from 50 mm to 60 mm. Show the num true stress…

A: Given lo =50mm l=60 mm K= 210 MPa n=0.27

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: What is its minimum width if it produces 1000 minima?

A: The expression for the dept of the slits is given by the expression, Dsinθ=mλ For the minimum width…

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: cm ỏ i 2 3 4 5 6 7 8 9 10 Main Scale Vernier Scale 1. The diameter of a certain circular shaft…

A: Smallest division of main scale =0.1 cm  Number of division in vernier scale =10  Least count =…

Q: name these lines

A: The names of the given lines is given below.

Q: An irregular shaped metal sheet is to be constructed with a measurement of 5.5m x 6.2m x 7.7m x 4m x…

A: given; dimension of irregular shape of sheet metal;          (1m=39.3701inch)L1=5.5m=5.5*39.3701…

Q: Give a steps by steps answer of the solution

A:

Q: Lab Activity 5H Calculating Radius End Points on a Lathe Part Use the illustration provided to…

A:

Q: 7. 62.4 x 10³ pascals into pound per square inch A. 9.04 B. 9.05 360 slugs into kilogram A. 5,254 B.…

A: 7. Option (B) : 9.05 lb/in2 8. Option (A) : 5,254 kg 9. Option (C) : 0.58474 lb/ft2

Q: 1. An engineering manufacturing company has established that the relationship between the quantity…

A: Given: Quantity solved per month or demand per month=D And sales price for each product=p And demand…

Q: 1- A mold with dimensions of 3 cm x 15 cm x 8 cm is intended in a sand plumbing through an estuary…

A: GIVEN: Dimension of mold = 30cm×15cm×8cm. length of estuary= 8cm Area of gate or entrance = 3cm2…

Q: What is an inflection point?

A: In solid mechanics, an inflection point is defined as a point where the curve of a physical quantity…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.