where p is a constant. Perform this rearrangement in order to identify the value of p in your case.

Q: The diagram at the right shows vector F. If F =-Q, where Q>0, I(d) determine the value of F in terms…

A: The force F is making an angle of θ with +y axis  and x-component of Force = -Q where Q > 0

Q: The pipe assembly in (Figure 1) lies in the x-y plane. F = 130 N. Figure 200 mm 300 mm 200 mm 300 mm…

A:

Q: Figure 1. Length of line AC? Zradis 8.33" 10 5.83" 9.72" 11.33" Figure 1. Value of angle <BAC in…

A:

Q: For the following Figure: 1) Determine the magnitude of the vector V = V2- V1 ( 2) The angle which V…

A:

Q: 1.5m 4m 1 of 1 > Determine the magnitude of the moment of the force F = {501-28 j-80k} N about the…

A: The force vector is

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: For the following internal dovetail, if b is 40mm greater than c, m is 60mm less than b, h is 25 mm…

A: Given information, h is 25 mm, b=40+c, Find  Angle

Q: 2 Constraint indicated the name and where it should be

A: Given: To find: Where the constraint should be

Q: C.W. ;DRAW: 1-FRONT+TOP+RIGHT SIDE 2-FRONT SECTION+TOP SECTION FROM MIDD. +RIGHT SECTION FROM MIDD.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Y=Sinu, usxt ex डकत्र व '५

A:

Q: What is Line B?

A: Solution:

Q: Draw the aligned sectional view of the following solid

A: According to the given data, there are two projection views. We need to find The sectional view as…

Q: Write the general equation of the circle of center (0, 4) and radius 4. Figure is not required.

A: The generalized equation of a circle with centre at origin and radius = r units is as given below:…

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

A:

Q: Draw the three projection in sheet

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 1-23.Determine the length of side C of the triangle shown in Figure P1-23.

A:

Q: The arm in is subjected to five forces as follows: F1 = 135 N, F2=98 N, F3 = 210 N, F4= 56 N. If the…

A:

Q: y 4+B 5+C 2 3. 1.Find The size of the area number 1 (triangle) 2.Find The center of the numbered…

A: Given data: h1=3+Ab1=4+B Need to determine the centroid and area of the shape 1.

Q: 0.75' C 4.5' Z 21-4 D A a 2 0.5' 2.5' B 10.5 X

A: (a) 2z ft(b) 0.5x+0.5y ft(c) -4.5x+0.75y+2.5z(d) -3.9x+y(e) 0.5x+0.5y-2z(f) 0.6x+0.25y-2.5z(g)…

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: Based on the figure identify only the relative polar coordinate of each point. The answer would be…

A: In this problem, cartesian relative coordinates are given and we have to calculate the polar…

Q: What is the angle between the x axis and the resultant? F2= 40 N y F, = 80 N 4 60° 3 (A

A: Given Data : F1=80 N F2=40 N F3=60 N

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: n the figure, front (1st picture) and left (2nd picture) views of a machine part are given. Based on…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: The tool starts at point P1 (X-50.0,Y-15.0) and goes around the part counterclockwise. It then goes…

A: CODES USED IN THE PROGRAM G01 -LINEAR INTERPOLATION G03- CIRCULAR INTERPOLATION , COUNTER CLOCK WISE…

Q: FAB Find the Angle between Line AB and Line AC in degrees. (Hint: Dot Product).

A:

Q: Create a free hand oblique drawing of the three objects

A:

Q: 1. Give the rectangular coordinates of the point C (p = 4.4, q = -115, z = 2). 2. Give the…

A:

Q: Draw the following spring with all mensions in sheet (write down all the equations you used in the

A:

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: 1. Draw top, front and right side views of the bracket as shown in Fig.

A: Required Front view, Top view and Right hand side view are drawn using third angle method of…

Q: In the figure at the right, if 0, =02 = 0, then a. T =w/(2 sine ) b. T; = w C. T+T =w d. T. w

A: The free-body diagram at the point of intersection of the three cables can be drawn as below,

Q: Q 114 Calculate the angle between the two vectors that makes the relationship AB = A correct?

A: Given question: Calculate the angle between the two vectors that makes the relationship A·B = A.

Q: In the drawing, arm A is being driven back and forth in the direction of the arrows. It is connected…

A: Solution: Given Data: Screw B is lowered towards the end of arm A.   To Find: What happens to the…

Q: Need you to draw orthographic views of this object.

A: The required orthographic views are drawn using third angle method of projection.

Q: Figure 4 shows the block diagram of a mechanical system. Given m3=3 Kg; m2=4 Kg; B1=5 N-s/m; B2=6 N-…

A:

Q: Can you solve the force applied in x,y, and z in the image?

A:

Q: Find: centroidal centroidal lx = ly= Ix, = ly =

A:

Q: 6 2 0 2 + 8- 1. Determine the area of the shape 2. Determine the moment of inertia about the y-axis.…

A:

Q: If P1= 400 N and P2 = 65O N, * Calculate EF, and EF, using x'and y'axises y y' x' P1 2. P2) 30

A: