When the force P reached 1620 lb, the wooden specimen shown failed in shear along the surface indicated by the dashed line. Determine the average shearing stress along that surface at the time of failure. (Round the final answer to the nearest whole number.) 0.6 in. Steel Wood 3 in. The average shearing stress is psi.

When the force P reached 1620 lb, the wooden specimen shown failed in shear along the surface indicated by the dashed line. Determine the average shearing stress along that surface at the time of failure. (Round the final answer to the nearest whole number.) 0.6 in. Steel Wood 3 in. The average shearing stress is psi.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.
Figure 2 shows the stress at point A of I-section beam. status given. a) Calculate the principal stresses, location and angle. b) In a section a-a with an angle of 30 shown in the figure the stress components that will affect the existing plane calculate.
A test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. Anaxial load of P = 30,500 lb. produced a deformation of 0.00103 in. over a gauge lengthof 2 in. and a decrease of 0.000078 in. in the 0.5-in. thickness of the bar. Determinea. Poisson’s ratio,b. the elastic modulusc. the decrease in the 4-in. cross-sectional dimension.
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
Q2) The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.Imm shorter than the steel posts at temperature of 50 C, if the allowable compressive stress in steel is limited to 200MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10'C ? steel E. 200 GR A = 1600 mar Ae1 steel T 50'd Alusinam L-250M = 200 M. Aluminum Post E= 73 GPa A = 2400 Ma = 23 K10 l 150 MP. comp Figure 2
A rectangular hole 5 mm × 15 mm is punched in a 2.0 mm thick steel plate of by a load of 100 kN. Calculate the average shear stress of the steel.
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
What is the average stress at section B-B? (Figure 1) Note: Give me right solution with clear calculations. Choices also given.
At the proportional limit, the axial load of a 0.70-in-diameter bar was 5400 lb. A 2.20-in. gauge length on the bar has increased by 0.0040 inch. a) Determine the strain in the bar.b) Determine the elastic modulus (in ksi)
Determine maximum shear stress
The wooden beam shown is made by gluing together planks as shown. 8 kN/m Glue 80 mm A B 80 mm - NA 6 m 80 mm 160 mm Determine the maximum shear stress in the glue in kPa. (2 decimals)