When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?

Q: 1. Please tell which of the control valves the following symbols are? A B Pi- P2 PT

A: Given details: Note-According our guidelines I solved one question at a time please other question…

Q: Choose the symbol for check valve. Select one: d.

A: Check valves are the devices which allows the flow in only one direction. So, it is also known as…

Q: Technician A says that when using a flare-nut wrench, two wrenches must often be used. Technician B…

A: A flare nut is a nut used for connecting to tubes for compression fittings of ductile materials. In…

Q: If you reverse the valve of the faucet to reduce water flow what will happen to water that flows out…

A: If you reverse the valve of the faucet to reduce water flow what will happen to water that flows out…

Q: Technician A says all gaskets should be discarded during teardown to keep the work area clean.…

A: Gasket : A gasket is a mechanical seal i.e it is used to close up the gap between two mating…

Q: The primary function of a way valve is to pressurize and exhaust two working ports A and B…

A:

Q: Hydraulic valves and their actuators are more in weight and can handle less amount of pressure.…

A:

Q: What is the name of the component that opens the valves?

A: There is a special component on the valve which is used to open the value.

Q: 2)which one of the following valve does not contain check valve inside? A)unloading valve…

A: A sequence valve could be a pressure valve outlined to open when its set weight is come to,…

Q: What are the results and discussions in identifying the different components of the ICEs valve…

A: Engine valves are a primary component of the internal combustion engine and are used to allow the…

Q: Explain how the sterilizer in the drone works

A: Drones today use three and six axis gyro stabilization technology to provide navigational…

Q: Explain why piston skirt is made oval in shape? (A3)

A:

Q: identify the different components of the ICEs valve system.

A: The components of IC engine valve system are - Valve guide Valve stem Valve spring Cam and follower

Q: ration i

A: given: Methods for treating vibration in pumps

Q: Instruction: Explain why is it impOrtant t0 calibrate the pressure gauge.

A:

Q: Which of the following is normally used for controlled draining of a tank? Orifice Nozzle…

A: Explanation  Orifice: Orifice is normally used for controlled draining of water . It is also used…

Q: Define valve margin

A:

Q: Take any two valves used in oil industry and write a short note on it?

A: Solution:

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: es are favored because of their lower cost and lighter weight Correct answer plug ball poppet…

A: To select the correct options.

Q: What is the center type of this valve?

A: See the answer in the next page.

Q: Select the correct option Formerly it was very common to determine the capacity of a valve; however,…

A: Given:

Q: which of the following statements regarding relief valves is not true? A. A blown fusible plug must…

A: Which of the following statements regarding relief valves is not true? Answer: D. Spring-loaded…

Q: Choose correct answer: Which one of the following devices creates only flow? An external gear…

A: External gear pumps are  used for pumping water and other fluids. They are preferred in applications…

Q: too lean mixture is supplied to the engine and may be caused in:

A:

Q: 1- Explain with sketch the relief valve and its work 2- Explain with sketch the types of pressure…

A: GIVEN DATA- DIFFERENT TYPES OF VALVE GIVEN USED IN HYDRAULIC SYSTEM WE HAVE TO EXPLAIN IT WITH…

Q: a hydraulic tu the full scale of the full scal

A:

Q: how to repair a van

A:

Q: Steps of how to draw a valve of an IV cannula using

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: What are the results and discussions in discussing the function of each component of the valve…

A: A valve is a mechanism or natural item that opens, closes, or partially obstructs numerous passages…

Q: Technician A says that excessive engine oil consumption can be caused by low oil levels. Technician…

A: Answer:- Technician B correct.

Q: Describe an acceptable storage area for a cylinder offuel gas.

A: Storage cylinders are used for the storage of the fuel gases. These cylinders are made up of iron or…

Q: Technician A says that coolant hoses should be squeezed to check for hardening or softening.…

A: Solidly squeeze both the upper radiator and radiator hoses. They ought to feel firm, solid, and…

Q: during what stroke one valve is closed and the piston is moving downward in the cylinder

A: The following diagram shows the processes taking place in an otto cycle.

Q: Draw the system of Boiler, put a label.

A:

Q: Sketch the symbols of a poppet valve and spool valve. Label the terminals.

A:

Q: 2- Draw theoretical valve timing diagram and compare it with actual one.

A:

Q: what can happen when valve spring tension is too low?

A: When the valve paring tension become low, valve springs will become incapable of holding the valve…

Q: Which among the following is not correct statement on poppet valve. O a. Less wear on internal seals…

A: Poppet valves are used to control the rejection and admission of the intake and exhaust gases from…

Q: Mention some applications of non-return valves

A: Non-return valves: The valves which allow the flow of the fluid only in one direction is known as…

Q: What is the purpose of a check Valve?

A: The purpose of a check valve is to prevent back flow in piping system. It allows fluid to flow only…

Q: the metring valve portion of combination valve fails .technician A says that this means the entire…

A: Given data technician A says that this means the entire combination valve must be replaced.…

Q: The 3 basic oil seal designs to keep fluids from escaping around a rotating shaft are?

A: The three basic oil seal design to keep fluid from escaping around a rotating shaft are-

Q: What is the function of On/Off valve?

A: What is the function of On/Off valve?

Q: 1.1 List five different ways in which the pumping of fluids can be accomplished.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: What does the head pressure do If the suction pressure rises?

A: Given Data : Head Pressure Suction Pressure

Q: What causes coolant to leak from the water pump weep hole?

A: What causes coolant to leak from the water pump weep hole? Answer: d) A faulty pump shaft seal