What’s is the purpose of breaking in new disc pads

Q: what sort of gear

A: A gear is a spinning circular machine element with cut teeth (called cogs) that mesh with…

Q: Procedure on how to make the head of a meat tenderizer.

A: The procedure to make the head of a meat tenderizer is as follows: Step 1: Cutting a pattern of a…

Q: Under staticload or when static load is applied ,most of the machine elements re failed  True…

A: Under staticload or when static load is applied ,most of the machine elements re failed  True  False…

Q: ..... ..... will extend the life of the equipment

A: ................. Will extend the life of the equipment.

Q: ssume the approximate Elas in the cartilage at the time t he piece of cartilage experie

A:

Q: the tires. This is an example of If a tractor trailer truck receives a heavy load, the driver should…

A:

Q: ength than A

A: introduction: here we find is the statement is false or true

Q: Briefly explain the anodizing process with a neat diagram. b). Write the application of anodizing…

A: The electrochemical process of transforming the metal’s surface into somewhat more durable, esthetic…

Q: Indicates the strength of the bond in the grinding wheel that used on a grinding machine is known as…

A:

Q: Undersized production tubing will result in higher bottom hole pressure than optimum. Select one:…

A: Solution:

Q: and the restorer

A:

Q: Where should vibration transducers be placed?

A: The location and installation of the vibration sensor are two of the most critical parts of the…

Q: -Why tolerances are given to the parts? To reduce weight of the component Because it's impossible to…

A: Why tolerances are given to the parts? To reduce weight of the component Because it's impossible to…

Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something.…

A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior…

Q: aber of teeth for involute

A:

Q: Unilateral Tolerance is Total tolerance is in both the directions May or may not be in any direction…

A: Unilateral tolerance is the type of tolerance in which true profile is only permitted in one…

Q: What is Double-Acting Unbalanced Linear( Landing Gear). Give some application examples of it.

A: The landing gear is used in aviation structures which are used to give support to an airplane during…

Q: The subject is vibrati

A: F= movm = M -mot , 0≤ t ≤ t0k = 7.5 × 106 N/mc = 0.2 × 106 N -s/mm0 = 15 kg/sv = 2000 m/sM =…

Q: Do not use _____ on nuts and bolts unless someone has rounded off edges of the nut or bolt.

A: Solution:

Q: How is it possible to decrease contact resistance? By using different fluids for better matching O…

A: Contact resistance is the resistance that hinders the flow of heat by conduction.

Q: among the ruler and vernier caliper gave the least % err

A: Ruler and vernier caliper both are measuring devices.

Q: Explain viscosity in detail of the starting to essy way

A: INTRODUCTION :  A Fluid is a substance that continually flows when an external force is applied.…

Q: The possibility to make the required shape from the material is considered during the criteria for…

A: Material to make the desired shape is considered during the criteria of selection. Because during…

Q: What is an additive when referring to lubrication?

A: Lubrication additives are used to enhance the performance of lubricants and functional fluids.A…

Q: List six steps involved in performing a visual inspection.

A: Visual inspection is the method of checking for the defects using naked eye. Visual inspection is…

Q: Penetrant testing Procedure below with Dwell time, and Minimum three defect that can be detected…

A:

Q: Explain it properly with full defination and formula used

A: To find:-  Head loss formula explaination

Q: What is damping Vibration.

A: Given Data : damped Vibration.

Q: Cleaning of machine tool should be carried out daily. Select one: True False

A: When it comes to machine tools, it's extremely important to perform the proper maintenance on them…

Q: 1. Choose the example of good vibration * Guitar Seismic Bullet Train Physiotherapy tools 2. Choose…

A: given; (1) ⇒example of good vibration?(2)⇒example of bad vibration ?

Q: What is fitting mechanical

A: Fitting Process :- Assembling of various parts of the machine.

Q: True or False? Safety of the material handling process should be determined after the system is put…

A: The safety of material handling process should be determined after the system is put in place and…

Q: Connecting rod bearings are to be replaced. The journal measures 70.866 mm (2.790 in.)​. The…

A: The Size bearings for above requirements are U/S--0.381 mm (0.015 in) undersize.

Q: What are the concerns about dropping an item using a chain in place of a rope?

A: Both the chain drive and belt drives have a separate application, belt, and rope drives will be used…

Q: _1. What is a type of tool that used to loosen or tighten screws that have a star-like depression on…

A: As per bartleby guidelines we are allowed to solve only 1st  3 subparts if multiple subparts are…

Q: If you have finger rings, it must be removed before working in workshop. Select one: True False

A: Data given- If you have finger rings, it must be removed before working in workshop -----

Q: Briefly define the purpose, types and construction of the hardness measurement.

A: The principal purpose of the hardness measurement  is to determine the suitability of a material for…

Q: Are nails are considered as direct materials.

A:

Q: If the service information does not provide a loosening sequence for the cylinder head bolts, what…

A: Cylinder head bolts are loosened to open the cylinder in order to work on it. A cylinder head is…

Q: Which of the following statements about safetyglasses is true?a. They should offer side…

A: Goggles provide the most comprehensive impact protection by forming a barrier around the eye…

Q: What particular feature does a solid collet have that makes it safer than a split collet?

A:

Q: seconds. If the next inspection is to take place in 30 days, would it be safe to delay the…

A:

Q: What are crumple zones in cars designed for? absorbing the shock from bumpy roads changing the…

A: Please see the solution below

Q: What is the difference between corrective maintenance and preventive maintenance ?

A: Corrective maintenance is the process in which any task that corrects a problem with an asset and…

Q: Which one of the following statement is correct?

A: Option (a) Lami's theorem is applicable for three coplanar concurrent forces and in equilibrium. is…

Q: Which two of the defects below are from the polymer manufacturing process? Wrinkling a. Spatter b.…

A:

Q: The possibility to make the required shape from the material is considered during the criteria for…

A: Yes , it is true.