What would be the technical classifi cation of the followingturbomachines: (a) a household fan, (b) a windmill, (c) anaircraft propeller, (d ) a fuel pump in a car, (e) an eductor,(f ) a fl uid-coupling transmission, and (g) a power plantsteam turbine?

Q: If the electrical power used is to remain at 7kJ/s, but we still require to extract 80 kW of heat…

A:

Q: The following particular refer to atwo- row velacity-Compounded impulse wheel which fome of a Q. 1…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: With the neat diagram of the Gas turbine sketch all the internal parts of the typical gas turbine…

A: Schematic diagram of the Gas turbine:

Q: 75% (about 6574 hours f $0.0054 per kWh

A: This is a basic LCDE number cruncher to give a metric that permits the comparision of the…

Q: I am trying to find the mass flow rate of cooling water in the condenser  Known values T9 = 20 C,…

A: The objective of the question is to find the mass flow rate of cooling water in the condenser of a…

Q: Q No. 6: A turbine is to be installed where the net available head is 180ft and the available flow…

A: Given data h=185ftQ=900ft3/sf=60cycle(zB)max=5ftη=0.92

Q: A 3.2-litre spark-ignited engine with a centrally positioned spark plug and combustion at Top Dead…

A: Engine capacity = 3.2 LitrePiston speed = 8 m/sBurn angle = 25°Piston's stroke/distance =…

Q: The following particulars refer to a two-row velocity-compounded impulse wheel which forms the first…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: 4. The main feedwater pump of a PWR delivers water to the steam generator at a rate of 15,000 GPM…

A: Given: The rate of water delivery, Q = 946.3 liter/s = 0.9463 m^3/s The steam generator pressure, P…

Q: Q#2: the condenser of Geothermal Heat Pump will be cooled by A pipe with dimeter 3 cm buried in a…

A:

Q: A 1inch diameter nozzle there is water flows under 400ft head to operate a turbine. There is 90%…

A: Write the diameter of a nozzle.   d=1 in=1 in×1 m39.37 in=25.4×10-3 m   Write the head of the water…

Q: Figure Q3 (c)

A: given

Q: Determine the TDH at 4500 m3/hr on the below pump curve using the minimum diameter. 1180 A.P.M. 140…

A: Given: To determine: TDH at 4500 m3/hr Efficiency NPSHR

Q: what is the efficiency? what is the NPSHR? what is the motor power requirement?

A: (1):EFFICIENCY- The term efficiency can be characterized as the capacity to accomplish a ultimate…

Q: 1- It can use the nuclear energy by using- (A) Nuclear fission using Uranium. (B) Nuclear fusion…

A: Dear student,                    According to the guidelines I am allowed to answer only three…

Q: B4. A 6 pole DC shunt generator with wave wound armature having 386 conductors, has to supply a load…

A:

Q: The following particulars refer to a row velacity-Compounded impulse wheel which foams of a the…

A: Thermodynamics : It is a branch of science which deals with work, heat, energy. Also, it studies…

Q: Taking the Centaur upper stage from last week and assume it is spin stabalized. Model a nutation…

A: To model the nutation damper, we will use a reaction wheel mounted orthogonally to the spin axis.…

Q: time c. Action time d. Burning time e. Progressive burni

A: 1. Time Delay The rocket is allowed to coast at its maximum altitude and slow down as soon as the…

Q: alculate the power in the compressor, W(kW) Calculate the power-heat in the exchanger, Q(kW)…

A: Given data is

Q: Example \\ An Autocycle type engine has a compression ratio of 10 and the largest cylinder size is 1…

A:

Q: Explain with drawings the working principle of Hydraulic power plants.

A: Required: Working principle of Hydraulic power plant with drawing.

Q: h) Find for the Nozzle-Bucket efficiency, in per cent. i) Solve for the Turbine Gross efficiency. 1)…

A: For solution refer below images.

Q: 1)The three forces in figure create a vertical resultant acting through point A. if Tis known to be…

A:

Q: 5. Carbon dioxide is flowing in a conduit at 50 psia, 100 F, and a velocity of 50 f/s. Find the flow…

A: Mach number is defined as the ratio of the square root of the inertia force to the elastic force…

Q: 7. A four-stroke, 6-cylinder, 3.6 Itr SI engine, is designed to have a maximum speed of 6000 r.p.m…

A: Carburetion is defined as the mixture of proper amount of fuel with air prior to entering in the…

Q: For the figure shown below, what flow rate is required to produce 4,700 HP if the turbine is 72%…

A: Given:Turbine power = P = 4700 HPTubine efficiency = Diameter of pipe = D = 3 ftLength of pipe = L =…

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.