Answered: What would be the current (Id) in a…

What would be the current (Id) in a Silicon diode if, at a temperature of 100° C, 0.63 volts are applied to it. The Reverse saturation current (Is) of the diode at 27°C is known to be 3 Pico-Amp

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: Find the overall T-parameters of the following network.

A: Given circuit is a type of series connection of two port network. We can add Z parameters of each…

Q: What would be the resistance if a 4-band carbon resistor had the following color on it: red, green,…

A: In this question we need to find a value of resistance for the given 4 band colour code

Q: Q1: Using a 50 nF capacitor in the parallel RLC bandpass filter with a quality factor of 5 and a…

Q: .If Vab = 178240 Vrms in a balanced Y-connected three-phase generator, find the phase of the phase-a…

A: Given,In a balanced Y-connected three-phase generator,Vab=178∠4° VrmsConsidering the phase sequence…

Q: The load shown below is connected to a 360 V, 50 Hz three-phase supply with a positive phase…

A: The load shown below is connected to a 360 V, 50 Hz three-phase supply with a positive phase…

Q: An unknown load draws 15A when connected to a 240V AC source, when connected to the same circuit,…

Q: A diode conducts

A: Diode- When diode is forward biased it is short circuited in a circuit ideally. When diode is…

Q: Develop the following problems. Suppose each diode in the circuit shown in Fig. N'1 has a turn-on…

Q: 28 M. R3 RI R4 RS Ra R₂ ť Wat Self-paced 8 * First NINE prime numbers Obtain everything, prom Req to…

A: Here we discuss the calculation of Req & P1-P9

Q: B) For a system with the transfer function What is the DC gain of the system? 10s+200 G(s)=2+10s…

A: Given, The transfer function, Gs=10s+200s2+10s+100

Q: Describe dc biasing methods to find Icq and VcêQ for collector feedback and voltage divider type BJT…

A: 1) COLLECTOR FEEDBACK BIAS CIRCUIT

Q: 1. The de emitter current IE is: A. 2.62 mA 2. The ac resistance re is: A. 8.67 2 B. 9.9222 3. The…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: The net magnetic flux density of the stator of 2 pole synchronous generator is Bnet = 0.3x +0.193 y…

A: Solution is as shown below

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Ro 1.OKO www 20 kN VBB Bpc = 50

A: As per our company guidelines we are supposed to answer only first question kindly repost the other…

Q: In an RC circuit charging a capacitor, R and C are 100 2 and 22 nF, respectively. Find the new value…

A: Given: In an RC circuit charging a capacitor, R=100 ΩC=22 nF To determine the value of resistor if…

Q: explain the aliasing in the PAM Signal?

A: The analog pulse modulation techniques are classified into three types, which are mentioned as…

Q: 2 The total charge entering a terminal is given by q=10(1-e') mC. The current at t = 1.609 sec is…

A: Given, Total charge entering a terminal q=101-e-t mC Time, t=1.609 s

Q: calculate the Rn, In or Isc, and current at Zc using Norton's Theorem

A: The given circuit is as shown below,

Q: What is the luminous intensity of a 100 watt tungsten

Q: Figure 1 shows a BJT amplifier whose voltage gain is A = -115. The values of the components are…

A: The Given is BJT amplifier, voltage gain is A=115 To Determine the upper cut-off frequency of the…

Q: Using a decoder and external gates, design the combinational circuit defined by the following thre…

Q: 2. A non-uniform sheet charge is distributed along one-eighth of a spherical surface of radius 'a'…

A: (2) The given figure is shown below: It is given that: Radius of spherical surface=aSurface charge…

Q: Find the following parameters iflg = 15.2 μA and Ve 12 V for this transistor. a. lc b. B C. VCE d.…

Q: 40/30° V -jΖΩ V. 08 30 j6Ω 100 υπηρεσ 5/0° A

Q: B) For a system with the transfer function G(s) What is the DC gain of the system? 10s+200 s²+10s…

Q: _______ action eliminates the offset described above by moving the controller output at a rate…

A: This is the question related to the understanding of controller and it's various techniques.There…

Q: What types of PWM is shown in the figure? * Modulating Waveform Carrier waveform M₁ (b) O Unipolar O…

A: In case of unipolar pulse width modulation taken two sinusoidal modulating signal in outof phase…

Q: For the circuit shown in figure No 3 determine the value of RL. Which will make the Zener diode…

A: Load resistance: The resistance is the property of the of the material the resist the flow of the…

Q: Vab = 138 Vrms in a balanced Y-connected three-phase generator, find the magnitude of the phase-a…

Q: Calculate the R.M.S value of the current waveform shown in figure below. 6 45 7 8 9 10 11 12 t i(t)…

Q: .Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150.

Q: Q3:Obtain the solution of the following difference ec

Q: An RLC series circuit constructed with R-10 02, L= 2 H, C= 1 mf, for an AC source with angular…

A: Given circuit, Resistance, R=10 Ω Capacitance, C = 1 mF Inductance, L = 2 H Angular frequency,…

Q: In a 50 hertz circuit, containing a 10 microfarad capacitor, the capacitive reactance is Select the…

Q: What would be the resistance if a 4-band carbon resistor had the following color on it: red, green,…

A: These resistors have two bands for the resistance value, one multiplier and one tolerance band.…

Q: 1- As an electrical engineer, why you should cooperate with the civil, mechanical and Architect…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Rc LOKO Vcc RB www Bpc = 50 10 V…

Q: The neutral current

Q: Find the inverse Laplace Transform of the given function. 5/3s

Q: Example 4: Magnetic Forces on Current-carrying wire in magnetic field (a) Calculate the force per…

Q: A very long wire generates a magnetic field of 0.0070 x 104 T at a distance of 3.0 mm. What is the…

Q: : Draw the output shape flip-flop (D) in case the edge is n CK 딲 D

Q: R₁=56 20v A) RTOTAL = B) I TOTAL = CV-TOTAL = R67 E) V3 11 R3-20 R₂=55 R5=45 R6 = 3 R₁-252 R7 = 3

A: circuit is solve as Rt is calculated by series and parallel combination of resistance

Q: Given a Voltage Feedback CE amplifier with the following data: RF= 5 KQ, RE = 200 Q, Rc = 1 kQ, Vcc=…

A: Given: A voltage feedback CE amplifier has the following data: RF=5 kΩRE=200 ΩRC=1 kΩVCC=12…

Q: .For the following voltage and current phasors, calculate the apparent power in VA V = 122 < 15⁰…

A: Given,The voltage phasor value is,V=122∠15° VrmsThe current phasor value is,I=18∠46° Arms

Q: understandable way. • Use Block Diagram Algebra and DO NOT USE Mason Gain Method PROBLEM: Find the…

A: Given A block diagram is given.we need to find the transfer function of the block diagram using…

Q: 4. In your own words what is safety?

A: As this question is asked to an expert of Electrical Engineering, so, here will discuss about…

Q: An inductive impedance takes 11.5 A from a 115 V, 60 Hz ac supply. If the reactance of the inductive…

Q: A current of 2 + j 4 amperes is flowing through a circuit. The magnitude of current is

Q: what is meant by natural sampling,and flat-top sampling? 11:24 ص

A: The sampling frequency of a signal can be described as the rate of dividation of a signal at which…

Question

What would be the current (Id) in a Silicon diode if, at a temperature of 100° C, 0.63 volts
are applied to it. The Reverse saturation current (Is) of the diode at 27°C is known to be 3
Pico-Amp
LIL

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How is a solid-state diode tested? Explain.
A germanium diode has a current reaches 80% ofits saturation point at 115°C. Calculate the voltage and the ratio of the current for a forward bias of 0.8V to the current for the same magnitude in reverse bias when the temperature rises to 165°C.
In the reverse-bias region the saturation current of a silicon diode is about 0.1 A (T 20°C).Determine its approximate value if the temperature is increased to 50°C.
Determine the diode current at 20°C for a silicon diode. Is=0.1microampere at a reverse bias potential of - 10V
A silicon diode has a reverse saturation current of 50nA at room temperature (25degrees centigrade). If the operating temperature is raised by 50-degrees centigrade, what is now the reverse saturation current?
For a Silicon diode, the forward current is 109 times the reverse saturation current Is. What will be the value of the forward diode voltage? Assume eta to be 1.
Determine the diode current at 100°C for a silicon diode with reverse saturation current of 5 microamperes and an applied forward bias of 0.6 V.
In the reverse-bias region the saturation current of a silicon diode is about 0.1 μA (T= 20°C). Determine its approximate value if the temperature (25°C).
Given an input square wave with +15V and -15V peaks, and bias voltage V of 3V. Diodes are ideal. Resistor value of 330ohms. Draw the output waveform, solve, explain and clearly indicate voltage peak level. HA C V₁ R 10
In the reverse-bias region the saturation current of a silicon diode is about 0.1 µA (T = 20°C). Determine its approximate value if the temperature is increased 40°C.
Determine the forward diode current for a silicon PN junction diode when the applied forward biased voltage is 0.8 V at 36 oC. The reverse saturation current of that silicon diode is 15 µA.
Design a clipping circuit that will limit the output voltage to 5V when applying an input sinusoidal waveform with a peak value of 10V. Assume available diodes with voltage drop of 0.5V. Sketch the output waveform of the circuit.