What will be the notation of throat length of a fillet weld
Q: A fillet weld can be used to join which of the following joint types: *
A:
Q: Name three popular welding processes.
A: This question is based on the concept of welding
Q: efficiency of the joint ?
A: Given; Ratio of diameter of rivet to pitch of rivet is; dp=0.22We have to find the tearing…
Q: What are the grooves most often used for welding on mild steel pipe
A: Single V Single U Single J Single bevel grooves
Q: why are some weld joints grooved?
A: Welding is a material joining process in which two or more parts are coalesced at their contacting…
Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned
A: Fillet welding is the process of welding to weld the 2 metals at an angle or perpendicularly.
Q: A fillet weld can be used to join which of the following joint types: * O All of the Mentioned O Tee…
A: Correct answer: All of the mentioned
Q: In addition to continuously changing the weld pattern,what other changes must be continually made…
A: Considered to be the most challenging pipe position is the 66 or 45° fixed inclined position.…
Q: Draw the welding symbol from the following information. SINGLE J BUTT WELD CONVEX FACE SIZE 5 mm…
A: Given: Drawn the welding symbols.
Q: Why should there be a space between the plates whenmaking a fillet weld on thick plates of a tee…
A: Fillet welding refers to the process of joining two pieces of metal together when they are…
Q: 5 Which of the following appropriate methods are adopted for reducing distortion in weldments?
A: When materials are welded together, because of the uneven cooling the stresses are induced in the…
Q: Design the above joint using welded connection. The w=15mm. The required length of weld is:
A:
Q: What two units are used to show the minimum shearstrength of a spot weld?
A: Resistance welding comes in the form of spot welding. One of the simplest and quickest methods of…
Q: 6) Residual stresses in the GMAW joint can be reduced through O Use of low coefficient of thermal…
A: Residual stresses in the GMAW joint can be reduced through Increasing the weld metal volume
Q: Why should convex weld faces be avoided?
A: Excessive Convexity This discontinuity can produce a notch effect in the welded area and,…
Q: Draw the Welding symbol based on the data given • SINGLE BEVEL BUTT WELD • Flat FACE • SIZE 45 mm •…
A: Given data SINGLE BEVEL BUTT WELD Flat FACE SIZE 45 mm HIDDEN SIDE ALL AROUND WELD To Draw the…
Q: Why are all welds not inspected to the same level orstandard?
A: Information Provided: Not all welds undergo the same level or standard of inspection. Not all welds…
Q: What is the minimum acceptance criteria for porosity for visual inspection of lap welds?
A: Lap welding: When two metals are attached in a overlapping pattern on top of each other then this…
Q: some of the factors that influence the cost of making a weldment
A: Various factors affecting the cost of making a weldment: 1) The type of equipment used. 2) Required…
Q: 24. Why is it important not to strike the arc outside of the weld joint?
A: Welding is a fabrication process in which two similar metals or dis similar metal are joined with…
Q: 7) Which type of FSW technique prevents plate thinning and hooking at advancing side of the weld…
A: Weld thinning and hooking in friction stir welding has been an inherent issue which affects the…
Q: 1. What does the following welding symbol indicate? GTAW 100 (5) c-d b. C. d. 2. Describe the…
A: We can solve first question since the exact one is not specified. Please resubmit the question by…
Q: After the weld is set up and ready to begin, how mightthe welder want to check for freedom of…
A: Welder method for determine the degree of freedom
Q: A self-regulating arc is formed during GMAW: (while using small diameter electrode) if
A: Explanation A self-regulating arc or automatic welding we always used constant voltage power source…
Q: What bead pattern is best for overhead welds?
A: Vertical up overhead smaw is best bead pattern for overhead welding. While you're in the vertical…
Q: What helps hold the weld in place on a 4G weld?
A: 4G weld :- It is an overhead position used for butt welds. Welders need to hold the torch from…
Q: Why is a prototype custom fabricated before producing multiple weldments
A: Why is a prototype custom fabricated before producing multiple weldments
Q: What can happen to the weld pool if the torch movement is too long?
A: 'Weld pool' is a term used in the terminology of the welding process. Weld pool is the molten metal…
Q: Explain minimum 3 types of welding position for groove and fillet weld?
A: WELDING Welding is a manufacturing method through which two or more components are joined by heat,…
Q: 11)lf length of a fillet weld is I and leg length is h, then area of throat can be given by:
A: The length of the fillet weld is l. The leg length is h.
Q: In which of the following welding process heat and pressure is applied on the joint but no filler…
A: we are to determine which welding method requires application of pressure and no filler material
Q: 7) On increasing the diameter of the SAW electrode, keeping the same current and arc length Width of…
A: The depth upto which the fused metal extends within the base metal or the pass from the previous…
Q: weld is called for by the small triangle on the underside of the welding symbol?
A:
Q: Give two reasons for using standard letter designations and give two methods used to specify the…
A: Reasons for using standard letter designation 1) It can be easy to understand to everybody 2) It is…
Q: 2. Find the information from the following weld symbol. 15 3. What are the types of Cycloids?
A: From the figure, we can deduce the subsequent properties of the weld; (1) The type of weld is a…
Q: What may happen if the GMA welding electrode is allowedto strike the base metal outside of the…
A: given; What may happen if the GMA welding electrode is allowed to strike the base metal outside of…
Q: Design the above joint using welded connection. The required length of weld is: Answer:
A:
Q: report about Soldering.
A:
Q: What problem must be overcome if the amperage and voltage are lowered to make a vertical weld?
A: Vertical welding:- The vertical welding is defined as a weld is applied to a vertical surface or one…
Q: a. Show how the extent of the surfacing weld is indicated between the vertical centerlines in the…
A: Writing the procedure to organise the weld between the lines on the flat. (1) Let us consider that…
Q: On all CJP groove welds in butt joints transverse to the computed tensile stress, they
A: A groove weld is an aperture between two joint elements that enables room for the metal to be…
Q: Draw the welding symbol from the following information. SINGLE BEVEL BUTT WELD CONCAVE FACE…
A: To Draw the welding symbol from the following information. SINGLE BEVEL BUTT WELD CONCAVE FACE…
Q: In a welding symbol for a u-groove with a consumable insert on the other side. What is the 2 in the…
A: The tail of the welding symbol is used to indicate the welding process as well as its specification…
Q: Q1/ If the weld size equal to (1.1 cm) find the Umax for figure bellow?
A: Given:-
Q: Describe two methods of striking an arc with an electrode
A: There are two methods of striking an arc Scratching Tapping
What will be the notation of throat length of a fillet weld
Step by step
Solved in 2 steps with 1 images