What type of axle housing resembles a banjo?

Q: Which of the following is not considered as a lower pair

A: 1. Option (c)  Roller pair  is correct option. Explanation: As we know that line and point contact…

Q: An open V-belt drive operates under the following conditions: coefficient of friction between belt…

A: The tension in the slack side of the belt drive is T2 = 813 N. Therefore, option (B) is the nearest…

Q: What type of floating axle has one wheel bearingper wheel on the outside of the axle housing?

A: A full floating axle has one wheel bearing per wheel on the outside of the axle housing.…

Q: Words: Axles, Differential, Gear, Housing, Propelled, Ring, Side, Transaxle, Transfers,…

A: Since Yoo have posted question with multirple subpart in a single request we will solve first three…

Q: With a neat sketch explain the types of Drives used in automobile.

A: There are different types of drives used in the automobiles  Front engine - Rear wheel drive Rear…

Q: The force applied on the spanner handle while closing a nut generates a ___________   Select…

A: The force applied on the spanner handle while closing a nut generates a ___________ Answer: Moment

Q: Draw a neat sketch showing the linkage to operate brake master cylinder and describe the same.

A: The brake master cylinder is a part of your car's braking system that transfers pressure from the…

Q: life of the ball bearing w

A: Given; Load reduced to half on the ball bearing, then life of the ball bearing will be  ?

Q: When discussing the possible causes for a shudder during acceleration, Technician A says that a worn…

A: Shudder is taken place during acceleration at higher speed. The main reason of this problem is…

Q: With the aid of an appropriate diagram and labelling, elaborate the gear and belt trainswhich each…

A: Belt and gear trains both are used for power transmission. Both are forming a surface to surface…

Q: Define the term Torque?

A: Torque: Torque is defined as the multiplication of the force and force-distance from the given…

Q: write short notes on any two types of solid bearings?

A: A plain bearing, or more commonly sliding contact bearing and slide bearing (in railroading…

Q: What is benefit of bifilar suspension technique?

A: given: What is benefit of bifilar suspension technique?

Q: AFGMA stands for O a. Anti-Friction Bearing Manufacturers Assaciation o b. Anti-Friction Bearing

A: The full form of AFGMA is

Q: Design and model of a basic mobile platform (2 wheel drive)

A:

Q: what are the mechanical differences between 4 wheel drive, front wheel drive and rear wheel drive…

A: given; what are the mechanical differences between 4 wheel drive, front wheel drive and rear wheel…

Q: Give examples of calculation turning moment (torque) on the crankshaft piston

A: given data; Give examples of calculation turning moment (torque) on the crankshaft piston.

Q: Why is mixing different manufacturer’s bearings typically not recommended?

A: Bearing: It is a mechanical element or part which allows the relative motion between two parts and…

Q: Please name two type of locking nut, and explain how they function.

A:

Q: Interaxle differentials are being discussed. Technician A says the interaxle differential is located…

A: It is an separate differential gear box that locks the first and second differential in a tandem…

Q: Define the term Internal Torque?

A: Torque refers to tension and Based on the tension created the torque classified as…

Q: What is the proper amount of belt deflection, and what tool is used to determine the amount of belt…

A: ■ The proper amount of belt deflection is 1" (1 inch) for every 64" (64 inch) length of the belt.…

Q: What are the different types of grooves found in belt drive?

A: Belt Drives are  used to transmit powers from one shaft to another shaft while pulley at the same or…

Q: List the types of belt drives and chain drives, their operating principle, and their advantages (at…

A: The belts are used to transmit power from one shaft to another shaft by means of pulleys. The power…

Q: Explain any one type of ball bearing with a neat diagram and write their applications?

A:

Q: While discussing types of coil springs: Technician A says that linear-rate coil springs have equal…

A: Technician A:- Technician A is correct says that in case of linear-rated coil springs have equal…

Q: Which of the following is NOT true about the initial tension in a flat belt drive? OA. It should be…

A: A spherical joint is also known as ball and socket joint, allows three relatives rotation between…

Q: What is the meaning of bearing code 3303? What are the requirements for the use of it?

A:

Q: In deatails explain the methods and manufacturing of sliding bearings?

A: Bearing  A bearing is the element of a machine that restricts relative movement and reduces friction…

Q: When reviewing the service procedures for CV joints and drive axles, Technician A says that the axle…

A: The axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle as…

Q: all and roller bearings need to lubricated

A:

Q: 78) Technician A says when a driving clutch is released, the drive discs drive the driven discs…

A: Given Clutch assembly To find How the assembly works

Q: What are the advantages of a self-adjusting clutch?

A:

Q: What do disc drives with a high level of rigidity typically consist of?

A:

Q: What makes high-rigidity disc drives?

A: To determine: High-rigidity disc drives features.

Q: When rope drive is preferred?

A:

Q: In the operation of some automatic transmissions both blank and blank overrunning clutches are used…

A: In the operation of some automatic transmissions both blank and blank overrunning clutches are used…

Q: Derivation of the relationship between tensile strength, contact angle and friction coefficient of a…

A:

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given, Coefficient of friction, μ=0.15 Weight of the handle, W=15 N Applied force to the end of the…

Q: what would cause a final drive noise that is heard only when cornering? a. Incorrect tooth pattern…

A: When cornering the noise produced due to the worn differential gears. Due to lack of lubrication the…

Q: Explain what are the types of belt drives and illustrate each of the types of belt drive together…

A: A belt drive is used to transmit the power from one location to another location. A belt drive is a…

Q: Design a chain drive for 20hp and 800rpm with an output speed on other sprocket of 200-300rpm

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.