What relationship is observed with regards to the current across each resistor?Discuss the relationship of the current, voltage, and power of your connected circuit.What is the observed relationship in step 6? DataR1R2R3Simulated Dataiz = 0.40 AV; = 30Viz = 0.30 AV; = 30VSimulated ii = 1.20 AV; = 30VVị + V, + V;= 30 Viz= 1.90 AV;= 30VSimulated V|V.Computed DataComputed iiTComputedPower, Pi = 1.20 A+ i, +i;=P = 36 Wiz = 0.40 Aiz = 0.30 Aiz= 1.90 AP2= 12 WP3= 9 WP, = 57 WP =Step 6P + P2 + P; = 57 WV, = 30 Vi = 3.0 ASimulated VSimulated ii= 3.0 Aiz= 3.0 Aiz= 9.0 A

According to ohm's law Potential difference across the resistor = current in the resistor×…

What relationship is observed with regards to the current across each resistor? Discuss the relationship of the current, voltage, and power of your connected circuit. What is the observed relationship in step 6?

What relationship is observed with regards to the current across each resistor? Discuss the relationship of the current, voltage, and power of your connected circuit. What is the observed relationship in step 6?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Given the table below, answer the questions: a.)For the same resistance of the circuit, what happens to the current as you increase the applied voltage? b.)For the same applied voltage, compare the current for the three resistance values used. c.)Superimpose plots of current versus voltage for the three resistance values (plot 1 is current vs voltage for 200 Ω, plot 2 is for 400 Ω, and plot 3 is for 600 Ω). Determine the slope of each plot. Which plot has the highest slope? d.)What is the mathematical relationship between the slope and the resistance?
How can a Wheatstone Bridge be used to find the value of an unknown resistors' resistance within a circuit? Explain how this concept ties into voltage dividers.
a) What does the voltmeter show in the schematic? b) what does the ammeter show in the schematic? c) how much power is developed in the resistor R5? d) What is the replacement resistor for the entire circuit (disregarding internal resistances of the source and instrument?
We know a voltmeter must be connected in parallel, but what does that imply about its internal resistance? Is it really big, or really small? If the voltmeter is connected in series (don't do that!), how does it affect the circuit? Include a sketch to illustrate your reasoning.
What do you expect the resistance of a fully- discharged capacitor to be? Why? What do you expect the resistance of a fully-charged capacitor to be? Why?
Consider the circuit below. [Answer in 2 significant figures] a a) b b) value. c) L 0.25 A d) 10 Q2 >M 0.1 A R = ? 20 Ω www 10 Ω www I= ? What is the potential difference between a and b? What is the equivalent resistance of the circuit? 5Ω What is the current l? How much power is dissipated by the unknown resistor R? You should have a numerical
Problem2:. Consider the circuits shown below. (a) Write the equation for current using the junction rule. (b) Write two equations using loop rule (c) Use these equations to find I₁, I2, and I3? (b) What is the power dissipated across each resistor (1²R)? V₁ = 24 V 12 R₂ = 62 R₁ = 80 ½ 13 R₂=402 + ₂10 V
Consider the circuit shown below. The current through the ammeter is 2 A. d) Find V1. e) If point P of the circuit is grounded (that is VP = 0V), what is thethe voltage at point Q? f) What is the power dissipated by resistor R7?
Given the series-parallel circuit below, calculate for the current and potential difference across each resistor. Show complete step-by-step solutions for each unknown value. Summarize your answers by filling up the table provided.
In the circuit below, if resistor R₁=46.30, and resistor R₂-56.05, what is the equivalent resistance of this circuit in units of Ohms (N)? High potential I R1 R₂ 12 I + Low potential Note: It is understood that the unit of your answer is in Ohms (), however do not explicitly include units in your answer. Enter only a number. If you do enter a unit, your answer will be counted wrong.
Consider the circuit in the diagram, with sources of emf listed below.Randomized Variablesℰ1 = 25 Vℰ2 = 46 Vℰ3 = 2.5 Vℰ4 = 31 V a.) Find I1 in amps. b.) Find I2 in amps. c.) Find I3 in amps.
I need help finding the voltage across the 1500 ohm resistor and the current through the 3900 ohm resistor. Attached is a picture of the circuit.