What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01 m3/s and the total head loss h=13.8 m. Assume the flow is a turbulent. Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m)

What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01 m3/s and the total head loss h=13.8 m. Assume the flow is a turbulent. Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is pumped at a rate of 21.4 m/s from tank (A) and out through a 300.5 m pipe to tank (B). The surface roughness of the pipe is 0.046 mm. When the water levels are as shown in the given figure, the head provided by the pump is 70 m, Calculate the pipe diameter (mm) if the water temperature is 10°C (do not assume the water mass density and the ViScosity), Usef 0.02 for the first iteration and try only one more iterations (two in total) by using Swamee and Jain formula. Elevation 135 Elevation 140 m Tank (B) Tievation 100m Tank LA) Jund: Elevitions in Write the answer for any numbers after the declmal
A pump with an efficiency of 89.842 percent delivers water at a rate of 13.79 m3/s but with a leakage loss of 0.5 m3/s. The friction losses within the pump result in a 1 m head loss. What is the total dynamic head of the pump in meters if it has a mechanical efficiency of 98 percent?
Water at 20 Celcius degrees is pumped from a large reservoir through a pipe system which has a diameter of 79 mm and length of 13 m. The installation of pipe system is as shown in the figure below. Considering the mass flow of the water supplied to the pipe is 5,1 kg/s and the surface roughness of the pipe is equal to the 5 micron, please compute the total pressure loss of the system in Pascal.
m². -5 S Figure shows a portion of a fire protection system in which a pump draws water at 60°F (v =1.21 ×10¯ from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height h of the water level in the tank in order to maintain 5.0 Psig pressure at point A h 25 ft A Pump 2600-ft-long 8-in Schedule 40 steel pipe Flow Flow 45-ft-long 10-in Schedule 40 steel pipe B
A centrifugal pump is used to pump water between two reservoirs as shown in the bellow figure. The dimensions and minor loss coefficients are provided in the figure. The pump rotates at 1600 rpm, the water inters the impeller normal to the blades and exits at an angle of 45° from radial. The inlet radius is 5.5-in, at which the blade width is 7.09-in. The outlet radius is 8.66-in, at which the blade width is 6.7-in. The volume flow rate is 23-cfm. Assuming 100 percent efficiency, calculate the net head produced by this pump in cm of water column height, the required brake horsepower in W and calculate the pump capability to pump water to upper reservoir. Reservoir z3-2, = 22.0 ft (elevation difference) D = 1.20 in (pipe diameter) KL. entrance = 0.50 (pipe entrance) KL. valve I = 2.0 (valve 1) KL. valve 2 = 6.8 (valve 2) Reservoir Valve 2 KL elbow = 0.34 (each elbow-there are 3) KLe L = 124 ft (total pipe length) e =0.0011 in (pipe roughness) = 1.05 (pipe exit) exit Pump Valve 1
Please solve and answer the question correctly please. Thank you!!
Calculate the power output from the turbine if the turbine efficiency is 75% and velocity at the nozzle 3 m/s and diameter of nozzle 50mm. EL=50m EL=30m D=50mm T D=100mm D=100mm
2. A pipe 120 mm bore diameter carries water with a head of 3 m. The pipe descends 12 m in altitude and reduces to 80 mm bore diameter. The pressure head at this point is 13 m. The density is 1000 kg/m3. Assuming no losses, determine i. The velocity in the small pipe (7 m/s) ii. The volume flow rate. (35 dm³/s)
5. Calculate the power delivered by the oil to the fluid motor shown in the following figure if the volume flow rate is 0.25 m3/s. There is an energy loss of 1.4 N.m/N in the piping system. If the motor has an efficiency of 75 percent, calculate the power output. ( Oil (sg=0.86) Motor Flow Diameter 15 cm- 10 m
help!
4. Water (p = 1000 kg/m³) is transferred from a large lake to an open storage tank located at elevation as shown in the Figure 2 below at a flowrate of 90m³/hr. The losses through pipe and fittings (hL) is given as 8m. Determine the mechanical efficiency of the pump if the shaft power required is 12kW. State the assumptions made in your calculations. 30 m WaterLevel Pump Centre Figure 2 Tank
oil is being pumped from an open tank A(elev = 110) to another open tank B (elev = 220m) with a total head loss of 15m of oil. The pump has a power rating of 210kW and an efficiency of 65%. Pipe 1 (D=200mm) connects Tank A and the pump while Pipe 2 (D=150mm) connects the pump and tank B. Calculate the velocity of flow in pipe 1, volumetric flowrate of oil, flowrate of pipe 2 and power output of the pump.