Problem 01. The pin-jointed frame in the figure below has members of cross-sectional area A=1200mm² and young modulus of elasticity of 200.5 GPa. If a vertical concentrated load of 1200KN (downward) and horizontal force of 800KN (to the right) are applied at Point D. Determine: a. The vertical displacement at D in mm. b. The horizontal displacement at D in mm. c. The stress of AD due to actual loads in kN. d. The stress of AB due to horizontal unit load. e. The stress of BD due to vertical unit load. 4m B 3m 3m F E

Problem 01. The pin-jointed frame in the figure below has members of cross-sectional area A=1200mm² and young modulus of elasticity of 200.5 GPa. If a vertical concentrated load of 1200KN (downward) and horizontal force of 800KN (to the right) are applied at Point D. Determine: a. The vertical displacement at D in mm. b. The horizontal displacement at D in mm. c. The stress of AD due to actual loads in kN. d. The stress of AB due to horizontal unit load. e. The stress of BD due to vertical unit load. 4m B 3m 3m F E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply-supported beam of length 3L is. subjected to the loading shown in the figure. P L P L L It is given that P = 1 N, L = 1 m and Young's modulus E 200 GPa. The cross- section is a square with dimension 100 mm. The bending stress (in Pa) at the point A located at the top surface of the beam at a distance of 1.5L from the left end is
Q.3) The Figure shown a beam with all dimensions. (a) Determine the bending stress at point H. 180 mm State whether the normal stress at H is tension or 12 mm compression. If the bending stress at point K is 9.0 MPa (Т). (b) Determine the magnitude of the maximum bending moment M: that can be supported by the beam. If the allowable bend 20 mm| 30 mm 260 mm stress is 165 MPa.
A beam of rectangular cross-section 40 x 20 mm is loaded with tensile force 1000 N as shown in figure. A B BO Calculate the shear stress on oblique plane at 0 = 45° A 0.625 MPa C 0.31 MPa F D 1.25 MPa
The T-beam is subjected to a bending moment of M = 150 kip in. directed as shown. Determine the maximum bending stress in the beam and the orientation of the neutral axis. Make sure you check all possible points (corners) for max stress and/or state other reasoning for the point that you pick. Answer: [σmax = 3.33 ksi, β = -63.1°]
The pin-jointed frame in the figure below has members of cross-sectional area A=1200mm² and young modulus of elasticity of 200.5 GPa. If a vertical concentrated load of 1200KN (downward) and horizontal force of 800KN (to the right) are applied at Point D. Determine: a. The vertical displacement at D in mm. b. The horizontal displacement at D in mm. c. The stress of AD due to actual loads in kN. d. The stress of AB due to horizontal unit load. e. The stress of BD due to vertical unit load. 4m B 3m C 3m F E
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 7.0 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at A. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1 m
Figure Q2(a) shows a cantilever beam that is subjected to a pure bending moment M = 3kN.m about the neutral axis (N.A) and the cross-section of a beam is shown in Figure Q2(b). Determine: (a) The moment of inertia about the neutral axis, InA. (b) The bending stress acting at point B and state whether it is in tension or compression. (c) The bending stress acting at point C (d) The maximum bending stress in the beam. M Figure Q2 (a) 20 mm B 150 mm C N 20 mm 150 mm 20 mm 250 mm Figure Q2 (b)
The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b = 5.6 in., d = 5.0 in., and t = 0.33 in. The internalbending moment about the z centroidal axis is M, - -3.50 kip-ft.Determine(a) the maximum tension bending stress (a positive number) in the beam.(b) the maximum compression bending stress (a negative number) in the beam.
For certain values of w and P, the maximum positive bending moment in the beam is +7044 lb-ft, and the maximum negative bending moment is -8873 lb-ft. The cross section of the beam is shown. The pertinent section properties of the cross section are e = 2.90 in., f = 1.30 in., and I,= 18.3990 in.4. Calculate (a) the maximum tensile bending stress and (b) the maximum compressive bending stress that is produced in the beam. Enter your answers with the appropriate sign. B D b d y
The beam shown in the figure is subjected to a moment of M = 50 kN.m. Determine the bending stress at point A and B.
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: F w (x) = E, ( - +4) %3D Ely 8. The value of E is 200,000 Nmm 2 and the values of ly is 20 x 106 mm4 The maximum value of z for the beam cross section is 20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm? Express your answer in Nmm2, as a number to 2 dp, without the units.
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?