WHAT IS THE TORSIONAL SHEAR STRESS AT THE OUTER SURFACE IN MPa? (2 decimals)

Q: The three dimensional rigid block in the figure is considered to be weightless and is under the…

A: The given figure is shown below:

Q: Let strain rosette shown in figure computed the values of strains at the built in end and in NA of…

A:

Q: The coefficients of friction between the block and the rail are Mg = 0.25 and Mk = 0.20. Given: P2 =…

A:

Q: Two vertical forces are applied to a beam of the cross-section shown. Determine (a) the maximum…

A:

Q: Calculate the stresses that will occur at point A in the adjacent figure. r=10mm

A: Given, Fz = 150 kNFy = 150 kNτ = 50 kN.mThere are three stresses at point A normal stress, bending…

Q: iven data: L1= 490mm L2=420

A: Draw the diagram From the above diagram sinθ=0.765, Cosθ=0.656Sinα=0.677, cosα=0.830 Calculate the…

Q: 125 mm 100 mm Y=si.15 mm 50 mm h - re 25 mm 25 mm

A: Given data: Taking top width as 100 mm then only y=81.25 mm. M=11.3 KN-m

Q: YA 20 mm 20° 100 mm 80 mm M

A:

Q: POISSON'S RATIO, µ It is the ratio of indirect strain to direct strain Formulas: H= Eindirect…

A:

Q: The shear center of the U-section element given in the figure below is shown with S and its…

A: step 1-

Q: 12 ksi 30 ksi - Change the horizontal normal stress from 30 ksi to 14.5 ksi - Calculate the…

A: Given:- The horizontal normal stress changes from 30 ksi to 14.5 ksi The shear stress = 12 ksi To…

Q: Plane Stress In the stress element given in Figure 3, WITH MOHR CIRCLE; (a) Determine the principal…

A: Principal stresses: Principal stresses are the utmost and minimum value of normal stresses on a…

Q: M 12 m. 60° Sin. 40 lb Problem 03.114.b - Location of the resultant force Locate the points where…

A:

Q: Consider the three forces shown in the diagram below. What is the net moment created about the…

A: F3= 55lb kF2= 45lb jF1= 65lb iForce F1 does not produce any moment about x-axis,because F1 is…

Q: In the attached image, stresses are acting at a point on the free surface of a stressed body. Here,…

A:

Q: what is the largest allowable intensity wo of

A:

Q: The bar shown determines: a) The internal force in section AB, BC and CD. b) The approach or…

A: Given, Cross sectional area=50 mm2 Modulus of elasticity=200×109 Pa

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Given Data  Find the angle corresponding to the orientation of maximum in plane shear stress.

Q: PROBLEM 1 For the area shown, do the following: a. Determine the centroid with respect to the…

A:

Q: The plane state of stress (shown in the following Figure) is for a point p inside a given body under…

A:

Q: If the beam is subjected to a shear force of V = 80 kN, determine the shear stress developed at…

A: Considering the section below:

Q: What is the horizontal and vertical component

A: To find horizontal and vertical component of 3kN force

Q: orizontally, not vertically. For this to work, there needs to be a resisting force, F, that holds…

A: Diameter of jet(d)=81mm Velocity of water through jet(V)=23m/s To find force required to hold the…

Q: What is the value of angle θ in degrees? B. What is the magnitude of force T?

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A: Step 1: Given:σx​=10ksiσy​=29ksiτxy​=6ksiTo Find σx′​,σy′​ and τx′y′​ when θ=+40∘(anticlockwise)Step…

Q: support varies as shown, determine the force P applied to the plate and the distance d to where it…

A:

Q: A beam with a cross section shown as the shaded area below is subjected to an internal bending…

A: Given :

Q: Determine the orientation of principal planes of stress. Enter your answers in degrees to three…

A:

Q: Solve

A:

Q: Question-2: The cross section of the bar in the figure a) Calculate the stress(tension) values at…

A: Find: (a) Stress at points A, B, C (b) Stress distribution in the section

Q: A cross section of a beam is shown. If the beam is subjected to a positive moment, which bending…

A: Moment is constant

Q: A column is constructed using four A992 steel angles that are laced together as shown. The length of…

A: Given :

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A:

Q: Examine the 2D frame shown to the right. Solve the problem with the following set of properties: E =…

A:

Q: Degree of Hyperestaticity

A:

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A:

Q: A rectangular beam carries a triangular load "w" as shown in the figure. Determine the following…

A: Assume a section x meters away from A Load ordinate at this section by similar triangles…

Q: 70 mm 235 mm 30 mm 275 mm 30 mm 30

A: the force and balance system can be resolve by simplifying the mechanism. the force is transferred…

Q: Shown below is the cross-section of a bridge pier. Knowing that the cross-section is symmetric and…

A: Given Data: The total width of the bridge pier is b=3.2 m. The total depth of the bridge pier is…

Q: Identify the Degree of Hyperestaticity and define the Main System, indicating the State of…

A: Step 1 include Basic probl idea Given data

Q: A solid circular pole is subjected to linearly varying distributed force with maximum intensity qo…

A: Normal stress at the base 150MPa qo=6.9kN/m L=6m P=80kN

Q: PROBLEM 1 For the area shown, do the following: a. Determine the centroid with respect to the…

A: Note: As per bartleby guidelines, only 1st 3 subparts need to be solved. For rest of the parts…

Q: If you replace the three forces shown by an equivalent force-couple system at point A, what will be…

A: Consider the figure,

Q: Help me urgent  Two forces are applied ti the bar shown in the figure. Determine the normal and…

A: The formula used to calculate normal stress is-  σ=PA+MIyWhere,P=Axial forceA=Are of…

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.