What is the strainer length required for a deep tube well giving a discharge of 8 litres per second ? Assume permissible entrance velocity of 2 cm/second. It is desired to have the strainer of slot sizes 20 mm x 0.2 mm with number of slots per cm length of the strainer as 100. (a) 8 m (b) 1 m (c) 12 m (d) 10 m

What is the strainer length required for a deep tube well giving a discharge of 8 litres per second ? Assume permissible entrance velocity of 2 cm/second. It is desired to have the strainer of slot sizes 20 mm x 0.2 mm with number of slots per cm length of the strainer as 100. (a) 8 m (b) 1 m (c) 12 m (d) 10 m

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

QI. s) Q1: A 1 m diameter well penetrates vertically through a confined aquifer (30 m) thick. When the well is pumped at (2712 m³/day), the drawdown in a well 15 m away from pumped well is 1.8 m; while the drawdown in another well 50 m away from pumped well is 0.5 m. Take the maximum head is 40 m. 1- Determine the transmissivity. 2- What is the approximate head in the first well? 3- What is the approximate head in the second well? 4- What is the approximate head in the pumped well for steady-state conditions? 5- What is the approximate drawdown in the pumped well?
A conduit is carrying oil ( S = 0.75 ) and its absolute viscosity is 0.25 kg / m-s. If the flow rate is 0.45 cu.m/s Determine the following • The entrance length • The length of the inviscid cone • The length of the profile development given the following situations 1. Circular pipe 800mm 2. rectangular pipe (Width = 800mm, Depth 1200mm)
A 2 ft diameter well penetrates vertically through a confined aquifer 50 ft thick. Whenthe well is pumped at 500 gpm in 1 day, the drawdown in a well 50 ft away is 10 ft andin another well 100 ft away is 3 ft. The storativity of aquifer is 0.0005. What is the valuefor transmissivity and drawdown? Note; the piezometric head is 100ft from datum.Combination of thiem & thies equation
1. THERE IS A LEAK IN A HORIZONTAL 300 MMDIAMETER PIPELINE. UPSTREAM FROM THE LEAK TWOGAGES 600 METER APART SHOWED A DIFFERENCE OF140 ???. DOWNSTREAM FROM THE LEAK TWO GAGES600 METER APART SHOWED A DIFFERENCE OF 126??? . ASSUMING ? = 0.025. HOW MUCH WATER ISBEING LOST FROM THE PIPE. show answer in litre per sec
Through the pipeline system in the figure calculate gauge and absulate presures at A and B
Problem 9-36 pipe bend shown is in a horizontal plane. A fluid weighing 8.615 kN/m enters the bend with a velocity of 3.5 m/s and a pressure of 280 kPa. Neglecting head loss, find the force required to hold the bend in place. The Ans 10.4 kN 65 200 mm O 80 mm diam
A pipe conveys water with velocity 360 m/min and pressure gauge shows 5 bar pressure under which the water is following. The pipe is located at 5 metre above the datum line. The sum of total head and stagnation head is m. (g = 10 m/s?). (assume 1 bar = 105 Pa) %3D
PH laborato Q4) Use water as a drilling mud to drill a well to a depth of 3000 feet. Calculate the pressure gradient to half of the well.
The oil derrick has drilled 5 km into the ground before it strikes a crude oil reservoir. When this happens, the pressure at the well head A becomes 25 MPa. Drilling "mud" is to be placed into the entire length of pipe to displace the oil and balance this pressure. Assume all pressures are gage pressures (Figure 1) Figure 5 km Part A What should be the density of the mud so that the pressure at A becomes zero? Density of crude oil is 880 kg/m³. Express your answer to three significant figures and include the appropriate units. Pm= 1.39 → 3 kg/m³ Provide Feedback 國」? Submit Previous Answers Request Answer * Incorrect; Try Again; 9 attempts remaining
I need right solution with clear calculations. If you don't know the solution please leave it but don't give me wrong solution. A 100 mm diameter well is drilled to withdraw water from a 11 m thick confined aquifer having coefficient of permeability equal to 64.8 m/d. The depth of water below the piezometric level is 30 m and it falls 2 m in the well while pumping. Calculate the discharge from the well when the radius of the circle of influence is 50 m.
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine a) FMY (N) b) Fpx (N) c) Fpx (N) de = 100 mm da = 150 mm 30° A
Orifice meter with orifis cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2. The pressure gauge fitted upstream and downstream of orifice give reading of 19.62 N/cm2 and 9.81 N/cm2 respectively. Determine the value of dischareg using Cd=0.6.