what is the reverse indicator alignment method ?

Q: What conditions does Compatibility specify?

A: In the field of mechanics, compatibility means when there is continuous deformation (displacement of…

Q: I need help answering these three parts pertaining to the print provided below.   What term could be…

A: Note: We are authorized to answer one question at a time. Since you have asked three questions at…

Q: I need isometric view please correct

A: The required isometric view is drawn with 1 Grid= 1 Unit

Q: What type of square has a blade that can be tilted to angular settings?

A: Diemaker's square has a blade that can be tilted to angular settings.

Q: The drive belt of the lathe machine is noticed with excessive wear, maintenance step followed is…

A: The major problem of excessive wear failure in belts is due to misalignment of drive loading,…

Q: Sensing element - This takes the output of the sensing element and converts it into a form more…

A: The input signal can be anything which is measurable like pressure, temperature, weight, etc. and…

Q: State the OSHA safety procedures of performing oxy/acetylene cutting and other gas cutting process

A:

Q: What are the two basic types of indicator movements?

A: Dial indication gauge is the name of the precision measurement device that uses a needle and a…

Q: d) Is that possible? e) Draw a heat engine diagram of a perpetual motion machine. f) Is it possible…

A: following is the answer to the above question

Q: In a tap set, the plug tap is the final one and is also known as taper tap. Select one: True False

A: Plug Tap

Q: List five (5) non-continuous monitors for diesel engines which can be accessed by the scan tool

A: Non-continuous monitors for diesel engines :

Q: It is common practice to assign a larger portion of the location tolerance to the hole.

A: Fill in the blanks.

Q: When looking to upgrade your gear, what are the top three factors you should keep in mind?

A: To explain: Three factors that should keep in mind while upgrading the gear.

Q: Show the front view, side view, and top view along with the hidden lines

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Which one of given options is true? O Work surface after machining process transforms into machined…

A: Solution:

Q: he process of machining the start of a drilled hole to make a conical shape or angle is known as:…

A: Given: In this question multiple choice is given so we will learn about them one by one

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: How can the metronome be used as a training tool for performance appraisal?

A: Metronome is a device which makes a a tick sound with the passage of time. It is generally used to…

Q: how to position this locator on a plate base for a part to ensure conformance with the Production…

A:

Q: 16. If the chamfer lengths of Part No. 4005851 are at the low limit and the total dowel length at…

A: 16. If the chamfer lengths of Part No. 4005851 are at the low limit and the total dowel length at…

Q: Match each term with the correct definition. tool machine product system   a mechanical or…

A:

Q: Select appropriate sensors for a specified wire cutting system

A: To select appropriate sensors for a wire cutting system, it would be helpful to have more specific…

Q: What principle does the heading indicator work? 2. How does heading indicator give its reading?

A:

Q: Sketch and explain the working principle, parts, types and application of a Dial Test Indicator

A: given; Sketch and explain the working principle, parts, types and application of a Dial Test…

Q: scketch the front view and isometric view

A: GIVEN:

Q: A single centerline is drawn in Longitudinal Horizontal Circular All

A: 1) ALL   Centerline indicate a circular feature on a drawing. In 2D, most circular features look…

Q: Which functions of the engine management system ensures compliance with Australian Design Rules

A: vehicle safety, anti-theft and emissions are the functions of the engine management system ensures…

Q: (a) Why the connecting rod is made as I section? Why do some connecting rods have hole drilled from…

A: The connecting rod is a mechanical component that connects the engine's piston and crankshaft. In…

Q: This is a diagram of a domestic hot-water system. The gas valve is operated by the controller,…

A: Given : To find : Simplified faut tree Minimal cut sets Minimal path sets

Q: How does the fault tolerance used by SONET work?

A: Fault tolerance is a feature of operating systems that allows them to adapt to hardware or…

Q: What is meant by 'sensor bias voltage' and how is it used in an engine management system? (70-100…

A: It is asked to write about sensor bias voltage and its working

Q: Double cut files use a second set of teeth,perpendicular to the first set to produce a rougher…

A: The given statement is “Double cut files use a second set of teeth perpendicular to the first set to…

Q: State and draw two methods used to mount cylinders?

A:

Q: find the top view

A: According to the question Two views of the drawing are given  We need to find Top view

Q: Which tool is used to measure pitch of the threaded part? Select one: a. Screw pitch gauge b.…

A: To measure the pitch of the threaded part, firstly the type of thread is matched with the gauge.…

Q: In GD&T   When tolerancing elongated holes, no ____________________ precedes the tolerance in the…

A: When tolerancing elongated holes, no diameter symbol precedes the tolerance in the feature control…

Q: Before energizing the motor of a drill press, always ensure that the: Chuck key is placed in the…

A: To find : what needs to ensured before energising the motor of a drill press

Q: A car has an engine. The Engine has it's hoursepower and its number wchich is unique and assigned…

A:

Q: In stripping In > an-1 O True False

A:

Q: draw top and isometric view

A: According to the details provided in the question, we need to calculate the top view and isometric…

Q: A normal shaft layout is based on the existıng model as a starter Discuss a process to create a new…

A: A normal shaft layout will contain various components such as bearings, gears and pulleys. But if…

Q: 3. FRONT AND TOP VIEWS ARE COMPLETE. SKETCH AUXILUARY VEW OFF FRONT VIEW.

A: Given view front and top view  To sketch : auxiliary of the front view