What is the purpose of a power substation in a power system? a. To generate electrical power b. To distribute consumers electrical power to c. To transform voltage levels d. To measure electrical current Which type of power system is commonly used for long-distance power transmission? a. DC (Direct Current) b. AC (Alternating Current) c. Single-phase system d. Three-phase system www B 1-120 V =6 BL-√2/3/4 A L The power dissipated in the resistor R is a. 0.5 W b. 1 W c. √2 W d. 2 W The current in the figure above is a. -j2 A b. -1A c. +j +1¬A d. +j2 A

What is the purpose of a power substation in a power system? a. To generate electrical power b. To distribute consumers electrical power to c. To transform voltage levels d. To measure electrical current Which type of power system is commonly used for long-distance power transmission? a. DC (Direct Current) b. AC (Alternating Current) c. Single-phase system d. Three-phase system www B 1-120 V =6 BL-√2/3/4 A L The power dissipated in the resistor R is a. 0.5 W b. 1 W c. √2 W d. 2 W The current in the figure above is a. -j2 A b. -1A c. +j +1¬A d. +j2 A

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
Lighting arresters are used in power system to protect electrical equipment against a. Direct stokes of lightning b. Over-voltages due to indirect lightning stroke c. Power frequency over-voltages d. Over-currents due to lightning
What is the significance of a three-phase power system, and how does it differ from a single-phase power system?
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
1. A single phase AC circuit consists of a 25 2 pure resistance. It is connected to an AC supply of 230 V at a frequency of 500 Hz. Determine the following: a. current b. power consumed and c. equation for the voltage d. equation for the current
If you have 3-phase power and you need to step down (or up) in 3-phase voltage, how many single-phase transformers are needed? Explain.
How does a three-phase power system differ from a single-phase power system, and what are their respective applications?
Find,a. Currents ?1 and ?3.b. Source voltage ??c. Power factor of the entire circuitd. Draw phasor diagram. Find magnitudes and positions of all the quantities. Please show complete solution and round off answers up to the 3rd decimal place. Thank you!
What is the most important 2 reasons for using 3 phase electrical power systems?
Grounding methods in Power systems
60. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the real power. a. 65.3899 b. 392.4372 c. 397.848 d. 588.6559
74. The eddy-current loss in a 6.9 kV, 50 Hz transformer is 220 W. What will be the eddy-current loss of this transformer if it is to be connected across a 6.6 kV, 60 Hz source? A. 201 W C. 234 W B. 224 W D. 212 W