Answered: What is the pressure required to reduce…

What is the pressure required to reduce the volume of a brass block by 10%?[Given the Bulk Modulus of brass = 6.1 x 1010 Pa] * %3D

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: What pressure should be applied to a lead block to reduce its volume by 10% (Bulk modulus of lead =…

A: A lead block has to be under pressure in order to have its volume reduced by 10%..

Q: Q1: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN.…

Q: In a structure you need to place a 7.5 m steel wire that does not stretch more than 6.7 cm when a…

A: Given,

Q: A brass rod 5ft long with a square cross section 0.5 inch on a side is used to support a 520-lb load…

A: B=F/AL'/L=FLL'AL'=FLBA F is the load L is the original length B is the bulk modulus A is the cross…

Q: Find the minimum diameter of an | = 15.1 m long tungsten wire that will stretch no more than 7.00 mm…

Q: A circular metal column is to support load of 500 Tonne and it must not compress more than 0.1 mm.…

Q: Find the force required to stretch a 1.0 m steel wire of diameter 3.2 mm by 10.0 mm. Given the…

Q: 1 D=2 cm diameter and l = 2 m long copper rod is lengthened by force F = 350 N for Al = 0.2 mm.…

Q: A stainless steel tube with an outside diameter of 46 mm and a wall thickness of 5 mm is used as a…

Q: A uniform metal bar, one metre long, is placed symmetrically on two knife-edges separated by a…

A: We can use the formula for the deflection of a uniformly loaded beam supported at its ends: δ =…

Q: Give answers in scientific notation. A sphere of copper is subjected to 120 MPa of pressure. The…

Q: Ex./2: Find the increase in pressure required to decrease volume of mercury by 0.001% (Bulk modulus…

A: We need to compute-Increase in pressure(dP)=?The data given as-Change in volume (decrease)=dV=0.001%…

Q: Calculate the shear modulus (G) for a cylindrical steel specimen. Assuming the elastic modulus is…

Q: Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial…

A: Initial volume (V) = 1.28×10-6 m3 Pressure or Stress (P) = 5.05 GPa or 5.05×109 Pa Bulk Modulus (B)…

Q: A steel wire of diameter 1 mm can support a tension of 0.2 kN. Determine the diameter of a steel…

Q: Question 16: A cubical solid aluminium (bulk modulus = -V (dP/dV) = 70 GPa) block has an edge length…

A: Given that, Bulk modulus=-VdPdV=70 GPa Here we know that, B=VdPdV

Q: of aluminum part is 1.2 m and of the C0 part is 2.5 m. Aluminum Copper La 1:f it ie

A: Given data as per question radius of rod = 0.178cm length of copper part = 2.5cm length of aluminum…

Q: Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the…

A: Given data: Observe from the diagram, Total displacement of layers D = 2 mm Height of stripe L = 5…

Q: A sphere of copper has a radius of 3.00 cm and is compressed uniformly by a force of 4.00 x 10° N.…

A: Given that, Force (F)= 4× 10⁸ N Radius (r)= 0.03 m Bulk modulus (k)= 140× 10⁹ N/m² Let the final…

Q: : Two wires of equal cross-section one made up of aluminium and other of brass are joined end to…

A: We need to find- Ratio of lengths of two wires LAlLbrass=? The data given as-…

Q: A 3.7-carat diamond is grown under a high pressure of 58x109 N/m2. One carat is 0.200 g, and you can…

A: The volume change of a 3.7-carat spherical diamond when withdrawn from the chamber and exposed to…

Q: Calculate the work done in stretching steel wire of length 2 m and of cross sectional area 0.0225…

A: To find-Work done (W)=?Given-Length (L)=2 mArea (a)=0.0225 mm2=0.0225×10-6 m2Load (F)=100 NYoung's…

Q: In a structure you need to place a 1.7 m steel wire that does not stretch more than 3.7 cm when a…

A: Given that, Length steel wire = 1.7 m Stretched length = 3.7 cm Force = 417 N Young's modulus =…

Q: X A steel beam is placed vertically in the basement of a building to keep the floor above from…

Q: Determine the strain-stress relations of an isotropic material for a cylindrical coordinate system.

Q: 2. A tall building with a cross-section A, a mass M and a Young's modulus Y has a height L on Earth.…

A: The mass of the building is M Area of cross section is A Young's modulus Y Height of the building is…

Q: What pressure is required to reduce the volume of a lead block by 1% ? (Given : Bulk modulus of lead…

A: Description : In this question we have to find the pressure required to reduce the volume of lead by…

Q: For the beam and loading shown, determine the maximum absolute value of bending moment and shear.

A: Draw the free-body diagram of the beam.

Q: For safety in climbing, a mountaineer uses a nylon rope that is 65 m long and 1.4 cm in diameter.…

Q: A ceramic rod tensile test is applied to the cylinders and the strain value during tensile is…

A: Given that:Longitudinal strain, dL/L = 0.2%=2×10-3Lateral strain, dr/r =0.5× 0.04%=…

Q: If the shear stress in steel exceeds about 4.00 x 108 N/m2, the steel ruptures. Determine the…

A: Given Maximum Shear stress = 4 × 108 N/m2 Diameter of cylinder = 2.5 cm We have to calculate…

Q: An oil specimen has an initial volume of 597 cm³ and is subjected to 3.6 MPa pressure increase. The…

A: Initial volume V=597 cm3 Rise in volume △V=0.35 cm3 Rise in pressure △P=3.6 MPa=3.6×106 Pa To find:…

Q: A stainless steel tube with an outside diameter of 46 mm and a wall thickness of 5 mm is used as a…

Q: An aluminium (Bulk Modulus =70.0 GPa) sphere of radius 53.1 cm is dropped to the bottom of a 2.80 m…

A: We have givenBulk Modulus =70 GPaSphere of radius =53.1 cmDepth of dropped sphere =2.80 m

Q: A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N.…

Q: PROBLEM 2. The light rigid bar ABCD shown in Fig. P-252 is pinned at B and connected to two vertical…

A: P=41.29KN

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

What is the pressure required to reduce the
volume of a brass block by 10%?[Given the
Bulk Modulus of brass = 6.1 x 101° Pa]
*

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 kN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa. %D
A HOMEWRK-1: The average cross-sectional area of leg 3 cm² and all of body weight 700 N supported of this leg, and the amount of shorting (AL) = 0.15 mm find the length of this leg in meter if you know that young's modulus of the bone is 1.8 * 1010 N/m². ANSWER L = 1.157 m L? A--3X1=4 F. 100 $t015 u Javi
1 iron 40 cm steel 70 cm Henry has a rod that is made out of 2 parts. An iron and steel section. The iron section is 40cm long (Y₁=9.1 x 10¹⁰ N/m²). The iron piece is attached to a steel piece that is 70 cm long (Y,=7.0 x 10¹0⁰ N/m²). The rod has a uniform cross sectional diameter of 3.40 cm. Determine the total compression (in mm)when henry uses a compressive force on the rod of magnitude F=6000N. Look at the image provided to get a better understanding.
Ex. 44: When a liquid of volume 4 liter is subjected to an additional pressure of 5 x 107 N/m², the change in the volume is found to be 4 ml, calculate the Bulk modulus of the liquid. se betap saam, Gase uzme kan
Please asap
Homework QI: A specimen made from Titanium with diameter 4 mm subjected to force of 2500 N. The specimen extended by 0.422 mm. If the young modulus is 107 GPa. Find the gauge length of specimen.
When a certain liquid freezes, it expands about 10.0%. What would be the pressure increase inside an engine block if the liquid in it froze? (The bulk modulus of the liquid when it solidifies is 1.60 x 10° N/m².) N/m2 Need Help? Read It
Please Asap
Artificial diamonds can be made using high- pressure, high-temperature presses. Suppose an -6' artificial diamond of volume 1.00 x 10 m is formed under pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamond's bulk modulus to be B =194 GPa. Use the rules of significant figures.
Suppose a piano tuner stretches a steel piano wire 5.5 mm. The wire was originally 0.825 mm in diameter, 1.27 m long, and has a Young's modulus of 2.10 × 1011 N/m2. l0 = 1.27 ml = 5.5 mmd = 0.825 mm Calculate the force a piano tuner applies to stretch the steel piano wire in Newtons. F =
How large a pressure increase (in ATM) must be applied to water if it is to be compressed in volume by 1%? The bulk modulus of water is 2 x 10° N/m? and 1 ATM = 105 N/m? Select one: O a. 400 O b. 1080 O c 100 O d. 200 O e 50
As soon as possible