What is the negative effect of operation a contactor coil above or below it's rated voltage
Q: 8. What are the two necessary condition for a thyristor to begin conduction? 9. Define holding…
A: Thyristor is a p-n-p-n, four layers, three junctions semiconductor switching device. It has three…
Q: 10.a. A normal commutator will have which one of the following colors where the brushes contact the…
A:
Q: After a period of use, the tip of a soldering iron (or a soldering gun) becomes dark and ëncrusted"…
A: When the soldering iron or gun is used for a very long time without cleaning, there is deposition of…
Q: In what way are the main power contacts of a contactor different from auxiliary contacts
A: Power contacts and auxiliary contacts differ not only technically but also in the context in which…
Q: What will happen to the fan if the rating of the fuse is 4A? Explain How does the resistance…
A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…
Q: 2. In what conditions will the thyristor continue conducting? How to turn off the thyristor?
A: Condition in which thyristor will continue conducting : The main condition for a thyristor to be…
Q: i) a) Draw the symbol and schematic diagram of moving iron meter. b) List out the range of basic…
A: as per question requirement i have to answer any two question. we need to draw the symbol and the…
Q: Training is required for: Qualified electricians only. b. Only those workers who work on or near…
A: Bartleby has policy to solve only first question and incase if it has subparts then solve only first…
Q: Explain why the inrush current to an ax contactor coil is much higher than its normal operating…
A: In DC coil, the load is resistive, thus the current through coil after contacts closing and normal…
Q: What happened if the DC voltage in the clamping circuit is replaced by source?
A: A Clamper circuit is a circuit with an AC input source, a capacitor and a DC reference voltage. The…
Q: What will happen if the DC voltage in the clamping circuit is replaced by an AC source?
A: A clamper circuit converts an AC signal to a DC signal. In fact, clamping circuits can be used to…
Q: Draw an elementary diagram of a pressure switch controlling a motor starter
A: Elementary diagram of a pressure switch controlling a motor starter, A basic diagram is a type of…
Q: Once a thyristor begins to conduct, what condition is necessary for conduction to cease?
A: In this question we will write the conditions required to turn off an SCR...
Q: combinations of switches
A:
Q: What provides motor running overcurrent protection for the dryer
A: The dryer's motor has an integral thermal overload safety in compliance with NEC 422.11(G) which…
Q: With a thermal circuit breaker what are the two main causes of heating of the bimetallic strip ?
A: Thermal circuit breakers are the most used breakers in many fields. As they have the fastest speed…
Q: (a) A basic permanent magnet moving coil (PMMC) movement can be converted into an ohmmeter with…
A: As per Bartleby guidelines we are allowed to solve only one question, as both questions are…
Q: lightning protection.
A:
Q: Draw a diagram of Dynamometer (Any types). With label and functions
A: The word Dynamometer has came from French word dynamomètre, which consists of two words dunamis…
Q: How much voltage will be applied to coil 1CR when it is energized?
A: On the energization of relay coil 1CR, the NO( Normally Open) switch closes, the 1CR now connected…
Q: grounded electrodes that are driven rods require a minimum of _____ contact with the soil.
A: Answer is 8 feet.
Q: Switch Type Rotary Switch (6 way) Symbol Voltage Current No. of pins Contact& Insulation Resistance…
A: Rotary Switch: It is a switch operated by Rotation.There are many applications using Rotary switch…
Q: searches on the types of fuses and switches.
A:
Q: Make a labeled circuit for pre-engaged type starter
A: Pre-engaged type starter - The pre-engaged starter motor is employed for high-compression engines…
Q: Why are electric heaters staged
A: There are many ways to control an electric heater: modulating (0-10Vdc), pulse (24Vac or dry…
Q: Explain the function of Ballast and Starter in the discharge lamp
A: The starter in the discharge lamp is "simply timed-switch". Which allows current to flow through the…
Q: Explain how a shading coil prevent an ac contactor from chattering
A: A shading coil is a single or a few turn of electrical conductor located in the face of the magnet…
Q: List 3 type of operating mechanism for magnetic contactor
A: Magnetic contactors are a type of electrical relay found on electric motors. They act as go-between…
Q: switch
A:
Q: electrical machines Explain how the experiment is done by drawing the connection diagram of the…
A: Explain how the experiment is done by drawing the connection diagram of the alternator idle test.…
Q: What is the common term for the sudden flow of current to an incandescent bulb or motor
A:
Q: a) Draw the symbol and schematic diagram of moving iron meter.
A: The given questions are different. As per bartleby expert policy, only one individual question is to…
Q: Discuss any two types of the lightning arresters. Please don’t handwringing
A: Lightning arresters are used to protect the electrical equipment ( installed in open space ) from…
Q: Explain by drawing how intermediate switch is working in ON and OFF position.
A: It is a very useful switch with four terminal and commonly used when we need to control a light…
Q: A 110 volt ac has been rectified by an SCR to power an egg incubator heater. If it is fired at every…
A: Given, Case 1: Input voltage V1= 110 volt AC Firing angle (alpha1) = 80°=80*pi/180 radians Case 2:…
Q: In the distribution board is used to protect human from the electric shock SWITCH
A: ELCB: ELCB stands for Earth Leakage Circuit Breaker. When a current leak occurs due to insulation…
Q: Which curve represents life of the lamp? D E A % NORMAL VOLTS O curve B O curve D O curve C O curve…
A: Incandescent lamp: The incandescent lamp is an electric light with a wire filament heated to such a…
Q: What can you do to reduce or eliminate the possibility of receiving an electric shock when working…
A: While working on electric circuits, possibilities of getting shocks is more. Therefore to eliminate…
Q: Which of the following is connected to the float of the fuel sending unit? A. switch B.…
A: The fuel sending unit is a potentiometer that is adjusted by a float which is attached to rod. When…
Q: For the inductive proximity switch shown below define the voltage level of the black colored wire…
A: 1) we can see 25 V supply given to sensor. Also from given we can see inductive sensor work below…
Q: Sketch the circuit for a double-switch and explain its working.
A: The circuit diagram for a double-switch is given in the following figure:
Q: Explain how DOL magnetic starter works step by step with diagram and pictures.
A: The DOL method which is also known as the Direct On Line starting method, It is started with rated…
Q: How does short circuit protection of automatic fuse take place? a) Magnetic b) Thermal c)Thermic d)…
A: B)Thermal Fuse is a piece of wire of a material with a very low melting point. When a high current…
Q: Explain with a neat block diagram the measurement of temperature using Thermistor (measuring system)
A: The measurement of temperature using Thermistor is as follows:
What is the negative effect of operation a contactor coil above or below it's rated voltage
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
- How much voltage will be applied to coil 1CR when it is energized?Explain the operation of the blowout coil used in dc contactorsparte A • Develop and explain the electrical schematic for the excitation coil in series.• Develop and explain the electrical schematic for the excitation coil in parallel.• Mention or cite examples about what use or application these 2 settings are used for.
- a) Draw the symbol and schematic diagram of moving iron meter. b) List out the range of basic moving coil meter operates for D.C voltage and current. c) What are the advantages of moving coil instrument? (any two)What are the two necessary conditions for a thyristor to begin conduction?and Once a thyristor begins to conduct, what condition(s) is necessary to cease conduction? Also, why is the conduction angle greater with an inductive load than with a purely resistive load?What will happen if the DC voltage in the clamping circuit is replaced by an AC source?
- Compare the design feature of ac and dc contactorsalculate the maximum force that should be applied via a pulling eye to a 70 mm2, 3-core copper cable,lf this is a low voltage cable with a PVC sheath, what is the maximum length of PVC pipe it can be pulled through?What Transient Voltage appears across the Circuit Breaker contacts at, or near Current Zero during the Arcing Period? O A. Arc Voltage O B. Recovery Voltage O C. Restriking Voltage O D. Critical Disruptive Voltage Co search