What is the current passing between the electrodes? Current passes through a solution of sodium chloride. In 1.00 second, 2.68 x 1016 Na+ions arrive at the negative electrode and 3.92 × 1016 C1- ions arrive at the positiveelectrode.Part AWhat is the current passing between the electrodes?Express your answer in milliamperes to three significant figures.• View Available Hint(s)1 Αφ?

The magnitude of total charge (both positive and negative ) is,…

Answered: What is the current passing between the…

Science

Physics

What is the current passing between the electrodes?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter1: Getting Started

Section: Chapter Questions

Problem 39PQ

See similar textbooks

Similar questions

A 0.460-mm-diameter silver wire carries a 10.0 mA current. Part A What is the electric field in the wire? Express your answer with the appropriate units. • View Available Hint(s) HẢ ? E = Value Units Submit Part B What is the electron drift speed in the wire? Express your answer with the appropriate units. • View Available Hint(s) µA ?
Q1) Ohm's Law (in electricity) states that the current (I) is proportional to the applied voltage (V). The constant of proportionality is the resistance (R). The resulting equation is: V = IR. This equation is re-arranged to: I = (1/R) V. Since this is a linear equation, the plot between V (on the x-axis) and I (on the y-axis) should be a straight line, with the slope being 1/R. In an experiment, the following data has been obtained for current for different values of the voltage. Voltage 1 2 3 Current 0.8 2.5 2.9 4.2 5.6 a) Determine the equation for the best-fit line from this data, by using the method of least squares. Equation: Plot the data points, and the straight line representing the equation that you found in part b) 'a'. (Note: the best-fit line will not pass through all the data points) c) Use the slope of the line to find the resistance. Resistance: LO
The following three questions refer to the figure below. a) Calculate the current through R₂. Use the following values: &,-8.1 V, ₂-6 V, R=R₂=7.90 and R₂ =2R₂. Enter your answer accurate to two decimals figures. E₂ R₁ ww E1 O a. 0.51 O b. 0.26 O c.0.34 O d. 1.03 R₂ www R3 a bl
R2 R1 d E2 - Enter only numerical answers on the spaces provided, units are already included. Answers must be entered in two decimals. Note that answers' accuracy was set to 0.05. Numbers in Scientific notation form should be entered with "E", e.g: 1.602 x 10-19 has to be entered as 1.602E-19. Given a single loop circuit with emfs E1 = 9.07V, E2 = 0.29V, resistors R1 = 7.70, R2 = 8.892, all connected in series to each other and a polarity of 51 is in opposite direction that of 2 (see a circuit attached). Using circuit analysis rules, the value of current flowing through the circuit is l= A? [NB: loop in the given direction of current.]
An electron is fired at a speed v 4.3 x 10 m/s and at an angle 8 = 39.7 between two parallel conducting plates as shown in the figure. If s 1.7 mm and the voltage difference between the plates is AV= 99.8 V, determine how close, w. the electron will get to the bottom plate. Put your answer in meters and include at 6 decimal places in your answer. Do not include units. The x-axis of the coordinate system is in the middle of the parallel plate capacitor. Round your answer to 6 decimal places.
An electron is fired at a speed v = 3.1 x 10° m/s and at an angle 0, = 36.8° between two parallel conducting plates as shown in the figure. If s 1.8 mm and the voltage difference between the plates is AV = 98.8 V, determine how close, w, the electron will get to the bottom plate. Put your answer in meters and include at 6 decimal places in your answer. Do not include units. The x-axis of the coordinate system is in the middle of the parallel plate capacitor. !!
The voltage V (volts), current I (amperes), and resistance R (ohms) of an electric circuit like the one shown here are related by the equation V=IR. Suppose that V is 1 increasing at the rate of 3 volt/sec while I is decreasing at the rate of amp/sec. Let t denote time in seconds. Answer the following questions. 5 dV dt = dl dt dl b. What is the value of dt? volt/sec (Simplify your answer.) OA. O C. amp/sec (Simplify your answer.) c. What equation relates to dR dt dR dV dt dt dR dt 1 dV dl +V- I dt dt dl dv =1+VdT dt dl and dt? OB. O D. d. Find the rate at which R is changing when V = 40 volts and 1= 4 amp. Is R increasing or decreasing? R is changing at ohm/sec. (Simplify your answer.) Is R increasing or decreasing? dR dt dR dt = 1 dv I'dt 1 (dV 1 dt V dl I dt F R www
R1 = 15 N, R2 = 10 N Data Experimental Data Computed % Difference Vr, Voltage Across Battery, V 10 V1 (Voltage Across R1), V V2 (Voltage Across R2), V I: (Current Flowing Through R1) A I: (Current Flowing Through R2) A Total Current, It (A): R2 R1 Page 1 I 2 Q +
1.Find the current (I1) from the following diagram. R2 = 2000 N R = 2500 2 R3 = 6000 n E = 12 V Current (I1) = A 2.The batteries in each of the circuits shown below are same and the wires have negligible resistance. Which circuit from the following dissipates the very high power? (A) (B) ohms ohms Sohm: 2 ohms (C) (D) ohms 2 ohms (E) ohms
A TV works properly under the voltage of 4V= 110 V with power P = 1560 W. Express the current I through the power P and the voltage AV. I = Calculate the working current of the TV in A. I = Express the resistance R through the voltage AV and the current I. R = |Calculate the numerical value of R in 2. R =
Review | Constants Part A A 8.6x10-4 V/m electric field creates a 2.5x1017 electrons/s current in a 1.3-mm-diameter aluminum wire. The density of mobile electron of aluminium is 6.0 × 1025 /m What is the drift speed? Express your answer using two significant figures. > View Available Hint(s) va = m/s Submit Part B What is the mean time between collisions for electrons in this wire? Express your answer using two significant figures. • View Available Hint(s) Hνα ΑΣφ ?
Part A An electric device draws 6.60 A at 240 V If the voltage drops by 20 % , what will be the current, assuming nothing else changes? Express your answer to two significant figures and include the appropriate units. HA Irinal = Value Units Submit Request Answer Part B If the resistance of the device were reduced by 20 %. what current would be drawn at 240 V? Express your answer to two significant figures and include the appropriate units. HA Innal = Value Units Submit Request Answer