What is simeconductor

Q: Please I need to resolve the question quickly

A: According to question: Since the frequency of Wien bridge oscillator is given as…

Q: Diiferentiate open loop system and close loop system

A: The desired output in an open loop system is independent of the control action, which is one of the…

Q: A 100 kV, 50 Hz supply is fed to a rectifier ammeter (using a bridge rectifier) through a capacitor.…

A: The PMMC meter problem is solved as below

Q: What will be the output voltage of this opamp circuit?

A: The voltage Vb  will be :

Q: Design the circuit of the following synchronous counter defined by the state transition diagram and…

A:

Q: Diode limiters or clippers in the audio portion of a receiver can typically remove sporadic,…

A: According to the question, we need to choose the correct option

Q: Q5: find the output waveform for the circuit in figure (3) Al ERSITY vin3D4 sin wt VR 2V Figure (3)

A:

Q: Discuss the thermistor

A: Brief description: In the above given question we need to define about thermistors.

Q: I need a theory from an experience (Characteristics of Bipolar Junction)

A: Bipolar junction have two different types of materials General configuration is NPN ,PNP. This…

Q: PMMC Instrument can be used to measure ac current if . is added ..... .. Rectfier Amplifier A/D…

A: In this question we need to choose a correct option.

Q: The upper cutoff frequency of this amplifoer is 22KHz. The output at that frequency is 6.71V p-p.…

A:

Q: Define chromatic dispersion and describe the causes for chromatic dispersion.

A: Dispersion is very important phenomena in optical fibre communication   Dispersion phenomena is…

Q: Ex. 295. Refer to Figure 295 Determine: 2%Settle Time, Peak Time, Rise Time, Percent Overshoot,…

A: Settling time : The time it takes for the output to reach and stay within a specific error band…

Q: an input voltage of 230 v is applied to a stepup chooper and the output voltage is 690 V. The pulse…

A: Given: Vin=230VVout=690VTOFF=115μs For step-up chopper  V0=Vin1-αα=duty cycleα=TONT

Q: Design a Buck Converter with the Following Features. Input Voltage = 50 V Output Voltage = 20 V…

A: Buck Converter:  It is a type of DC-DC converter where input voltage is being stepped down to get…

Q: What is the output waveform? Explain your answer. a) Sine wave b) Square wave c) +15V d) -15V + 2 1…

A: Given circuit is ideal op amp circuit with negative feedback in voltage follower mode( buffer…

Q: 11. Identify each of the op-amp configurations in Figure 12-63 || www om

A:

Q: A step up chopper has input voltage of 200 V and output voltage of 600 V. If conducting time of…

A: Given a step up chopper with, Input voltage, Vin=200 V. Output voltage, Vo=600 V. Conducting time of…

Q: WHAT ARE FREQUENCY DEMODULATORS

A: According to the given question, it is required to determine what frequency demodulators are. The…

Q: Transients: What is the time constant of the following circuit in milliseconds? R₂ R4 ULO…

A: In this question,   We need to determine the time constant?  For RL circuit Time constant= L/R

Q: How can the amplitude of the output voltage be increased?

A: This question is related to analog circuits. The amplitude of the output voltage can be increased…

Q: what are the structural differences between reverberating and converging circuits

A: The converging circuit: The converging circuit diagram is shown in the following figure:

Q: 2- For the circuit given below : Vin is a sine wave Vinpp=18 V and Vref=-0.7 V, Assume Vsat=+12V…

A: we need to draw the input and output waveform of the given opamp

Q: If the load current is 5 mA and the filter capacitance is 1000uF, what is the peak- to-peak ripple…

A: In this question,  Choose the correct option What is ripple voltage ∆V = Vm/2fRC = Im/2fC

Q: 19. Beginning in position I in Figure 13-70(b), the switch is thrown into position 2 and held there…

A:

Q: The secondary sensing element used in the given figure IS Differential transformer

A: The secondary sensing element used in the given figure is :

Q: The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain 24 V output…

A:

Q: vin D2 5 kn + 10 V ww D1 5 kn Vout Vin T - 10 Vt-* T/2

A: Dear student please find the attachments.

Q: + VL mm iL ic www iR Vo

A:

Q: 9. Sketch the output for the clipper circuts with the graph of the input sine wave. Label the…

A: The output of the clipper is as shown below

Q: Determine the period and frequency of oscillation for an astable multivibrator with component values…

A: The astable multivibrator generate square wave. It doesn't require any external triggering pulse.…

Q: C) What is a Transducer? With a neat sketch, explain the Measurement system using a piezoelectric…

A: