what does c3 equal

Q: Draw the block diagram of the following differential equation: a ² + y = 9²x dt² d²+3d+y= dx dt +29…

A: Given:a differential equation,we need to draw:the block diagram of the system corresponding to given…

Q: R + H3 G1 H1 + G2 H2 C

A: It is asked to simply the given block diagram

Q: Simplify the following ex pressions to sum of products and products of sums using K-map: Ka) (b) ab…

A: K-map is used to simplify boolean functions. It can be used to minimize sum of product and product…

Q: R(s) + G1 G2 G3 G4 +1 + G5 G1 FIGURE P5.5 Anter +A G6 day bindell C(s)

A: Given diagram,

Q: Q2: A program to calculate the sum of squares of numbers from 1 to n.

A: matlab program is written below

Q: By the aid of constant-voltage model, sketch the input/output characteristics of the circuit…

A: Given- Resistances values = 1 kohm and 1 kohm To find- Input output characteristics of the given…

Q: PLEASE LABEL AND DESCRIBE DIAGRAM

A: The given circuit diagram is:

Q: + Voc- 18V CE Ampiner Emiter Follower Re23 ka - 150 A 150 V- 15 mv R 12 K 1 ka 1 kO R250 n

A: Part (a): The capacitor acts as open-circuit in case of  DC analysis. Now, the circuit diagram is…

Q: Q.7 a) Ring and number the junctions of component in the below circuit. R2 R4 Input Q2 Output DI R3…

A: The above circuit consists of circuit equipment like Resistors, transistors, input, and output.

Q: In the circuit i1: %3D i1 12 is R1 R2 8 A Select one: O a. 2 A O b. 6 A O c. (-5) A

A:

Q: A Wheatstone Bridge is shown in Figure Q5. Determine R3 so that the Bridge circuit is in balanced…

A: aIn Wheatstone Bridge at the point of balance i.e. VAB=Vo=0 V.Both legs have equal voltage…

Q: I need help building this BJT amp circuit on a breadboard. If possible would you be able to show how…

A: Need to provide the Breadboard layout for the given Voltage divider biased BJT circuit.

Q: See Attached P3

A:

Q: reduce the following diagrams to a single block

A:

Q: O Given the information appearing in the Frigure, Fird the level of resistance for Ri e R3. RI O 14V…

A:

Q: (b) Prove the circuit in Figure Q.5 can perform the operation of adder/subtractor by completing…

A:

Q: Draw and label a voltage divider that generates 0.5V from an input of 1.5V. Then draw and label a…

A: To solve the above problem, one should know how to find the equivalent resistance for series and…

Q: c) The small signal current in R1 d) The small signal voltage vout

A:

Q: R2(Rx+Rnp)=R1(R3+Rnp)........(2) Rnp/Rmp=R1/R2.........(1) Substitute equation 2 into equation 1

A: To solve  the given equation

Q: C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of…

A: LVDT(Linear Voltage Differential Transformer) . It has a primary and two secondary windings . The…

Q: determine the following

A:

Q: Find the efficiency of the following circ +20 V R. 47042 22正 1000 µF R 22 pF 470 2

A: Given circuit is a class AB power amplifier(complementary emitter-follower pair).

Q: d. Reactive power and apparent power after compensation

A: A single-phase load has an active power of                      P = 2 kW power factor is cos(pi) =…

Q: Obtain the transfer functions C(s)/R(s) and C(s)/D(s) of the system shown in Figure R(1) Ge G₁ H H₂…

A: Introduction Transfer Function: For all conceivable input values, a transfer function shows the…

Q: c) What is the name and one of the advantages and one of the disadvantages of the current mirror…

A: Brief description: For the above given question we have to identify its name and we must mention its…

Q: How can i design (v1-v2)/3 operation using an opamp.

A:

Q: Try to draw the dynamic analog circuit diagram of the mechanical system in the figure. In addition,…

A: There are two types of conversion: 1. Mechanical to electrical system. 2. Electrical to mechanical…

Q: R3 432 R4 332 AO Reg = R1 142 R2 422 во

A:

Q: R9 RIo R12 R6 R7 Rt??

A: The modified circuit for the given figure is drawn below, Therefore, the calculations are shown…

Q: please just answer part g

A:

Q: Fig. P3.4 shows an electromagnet system for lifting a section of steel channel. The coil has 600…

A: The diagram of the electromagnetic system is shown below:

Q: Can you provide 6 types of bridge circuits? Its figure, function and application.

A: We have given the following problem Can you provide 6 types of bridge circuits? Its figure,…

Q: 1. Sketch the Vout and the currents for the given circuits shown below when a step input is applied…

A: To get the expressions of output voltage and current, first we transform the circuit in s-domain for…

Q: OR1 OR2 AND1 OR3

A: To find the resultant output of a digital circuit, it is important to understand the logic of each…

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).