What could be the Q output in the circuit in the figure? Please choose one: a. 010010 b. 010001 C. 011001 D. 010000 to. 011101 f. 010101 16:17 6.07.2021

Q: Draw the implementation and the timing diagram of a mod-12 with a straight binary sequence from 0000…

A: The flip flops are used as the memory elements. The flip flops can be SR, JK, D and T flip flops.…

Q: What is the value of the 8 digital bits that are represented as in the figure above if (Hint: the…

A: A)  NRZ L 01011001 There is a change in polarity of the signal only when the incoming signal changes…

Q: Design a full adder circuit to add the binary numbers A = 0, B = 1 and C = 1

A: According to question: Truth table of Full adder circuit:

Q: Q2: Design 4-bit Parallel-in to Parallel-out (PIPO) using RS-F/F. Draw the parallel output waveform…

A: The diagram for 4-bit Parallel-in to Parallel-out (PIPO) using RS flip-flop is shown below:

Q: Consider a 1 into 4 de-multiplexer.The data input and selection line waveforms for the demultiplexer…

A:

Q: In A/D converter, the maximum amount of error can be computed by dividing the voltage range over…

A: Given  An analog to digital converter  No of bits =10 Voltage range =0 to 6 volts  We need to find…

Q: What is not a possible solutions to improve performance ..... of PCM? a. Use of linear PCM codes b.…

A: 1) The signal to noise ratio in db is directly proportional to the number of bits per sample. Hence…

Q: Q8/Chose the correct answer for the output G of the following circuit C Assume that A= 111100 B=…

A:

Q: Mention several names of electronic devices that use the pulse signal processor in their work, and…

A: There are many analog and digital electronic devices which are used in digital signal processing…

Q: Write a 8 bit full adder using arithmetic operator  in dataflow modelling technique. Write test…

A: Vhdl library ieee; use ieee.std_logic_1164.all; use ieee.std_logic_unsigned.all; entity adder is…

Q: ; An experimenter uses a 10-bit A/D having a range from -5 [V] to +5 [V] to digitize a 35.0 [mV]…

A:

Q: (a) Construct a transition table and state graph for the circuit shown in Figure 5. Is the circuit a…

A: Moore circuit is the finite state of circuit . whose current output value are evaluate current…

Q: Design a counter that will output 1, 2, 3, 5, 8, 13 and repeat again.

A:

Q: 2. Design a 6 bit digital to analog converter with binary weighted resistive ladder network so that…

A: Digital to Analog converter (DAC) is a network that changes the digital input to the corresponding…

Q: a) Determine the delay (in terms of d) for each of the following 128-bit CLA designs when fan-in…

A:

Q: Convert the following hexadecimal numbers tobase-10 and binary:a.A b. 66 c. 47 d. 21 e. 13

A:

Q: A 12-bit linear PCM code is digitally compressed into eight bits. The resolution is equal to 0.03 V.…

A:

Q: Design a 6-bit digital to analog converter with binary weighted resistive ladder network so that the…

A: 6-Bit  weighted resistor Digital to analog converter (DAC) Given  Bit sequence =100100 MSB = 100 LSB…

Q: For a 5 bit ripple counter please

A: In a n - bit ripple counter relation between output and clock frequency is defined as =

Q: Show how two 7483 a four-bit parallel adders can be connected to form an eight- bit parallel adder.…

A: The 8-bit adder can be designed by using the two 4-bit adder by connecting them in cascade.

Q: esign a 3 bit circuit . Use Full Adders and display the outputs and Carry OUT and or Carry IN at…

A: full adder sum = A xor B xor C carry = A.B+B.C+C.A In 3 bit carryout of one will be feed as carry in…

Q: what is the output of (10101010+11001100) 0101110110 1100101110 O 1011000000

A: For answering this we have know the addition of following 0 + 0 = 0 carry 0 0 + 1 = 1 carry 0 1 + 0…

Q: • Draw the implementation and the timing diagram of a mod-12 with a straight binary sequence from…

A: 4 J-K flip flops are required to implement the MOD 12 counter with the count sequence 0000 to 1100.…

Q: A 12-bit counting converter with VFS = 5 V and fc = 1 MHz has an input voltage VX = 3.760 V. (a)…

A: (a) The expression for ADC output code is given by output code = input voltageoutput voltgae2n bits…

Q: Question/ Up on your understanding discuss a conversion of an analogue signal to digital bits…

A: The ADC is an analog to digital convertor. The machines understand the digital binary bits in their…

Q: In a . output signal fed back so that it subtracts from .the reference signal

A: In a closed-loop system, the output of the system is compared with the reference signal, and based…

Q: Show the binary addition algorithm steps fo the following: C=0.2 * (A+B), where A= 0.75 (ten), B=…

A: Given-A=0.75B=-0.4375C=0.2*A+B   =0.2*0.75-0.4375   =0.0625   =6.25×10-2 ⇒0×3D80000016

Q: How will be the reconstructed signal when fs >= 2fm?

A: How will be the reconstructed signal when fs >= 2fm? Examining hypothesis expresses that in the…

Q: Explain how a comparator becomesa 1-bit ADC

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: let AX=4567 H,SS=0105H and SP=0006H. Figure below shows the state of stack priorand after the…

A:

Q: V) Convert from Binary to Hexadecimal (a) 1001011010101112 (b) 11101100101.010101012 VI) Convert…

A:

Q: HW: Show the wired-AND circuit for a 10-input AND function using 74LS09 quad 2 input AND gates.

A: The design based on 74LS09s can be designed similar to same design with additional input functions.

Q: Q2 (a) Differentiate between convolution and correlation processes in the digital signal processing…

A: Convolution: It is a property to calculate the output of the system by convolving the impulse…

Q: TRUE or FALSE 9. A waveform can be enabled or disabled by both AND and OR gates. 10. An…

A: 9. A waveform can be enabled or disabled by both AND and OR gates. 10. An exclusive- OR gate output…

Q: A SOMA

A: The number of NAND/NOR gates required for a full adder will be 9. that is why NAND/NOR gate also…

Q: Design a counter that will output 0, 2, 1, 3 and repeat again.

A:

Q: QI/B/ Determine the analog voltage output for the Figure shown below if the waveforms representing a…

A: In this question,  Determine the analog output voltage Vo in the operation amplifier .  If the…

Q: Design a 6-bit digital to analog converter with binary weighted resistive ladder network so that the…

A: Given values,  Analog output is -X1X2 V  Bit sequence is 100100

Q: Problem_#08] The waveforms shown below are inputs to a 4-bit binary counter. The input signals…

A: Given inputs      Counter doing counting only when CTEN is high, otherwise it remain to its present…

Q: Determine the output of the binary-weighted resistor D/A, if the waveforms representing a sequence…

A: The digital to analog converter (DAC) converts the digital input to analog output. The resolution is…

Q: Problem_#08] The waveforms shown below are inputs to a 4-bit binary counter. The input signals…

A:

Q: 1- Explain the main process to convert a continuous time signal into digital one. Show the different…

A: Explanation: With the purpose of processing continuous-time alerts the use of a discrete-time…

Q: 2)Convert 11011010100100012 to hexadecimal. A)895B B)CA11 C)53AC1 D)DA91

A:

Q: 2. An A-to-D converter must cover a range from -24V to +24V, with a quantization resolution of 20 mV…

A:

Q: a) Convert 348710 to hexadecimal. b) Convert D74E958316 to binary. c) 6ABF16 to decimal.

A: Different methods are available  Here iam going with very basic methods

Q: To Design carry look ahead adder (CLA) that add 6 numbers (4- bit) can using

A:

Up-down counter

In digital logic and computing, a counter is a device that stores (and sometimes displays) the number of times a particular event or process has occurred, often in relationship to a clock. A sequential digital logic circuit is the most common type with an input line or clock and multiple output lines. In the binary or binary-coded decimal (BCD) number system, the values on the input line represents a number by several flip-flops connected in a cascaded manner. They are manufactured as separate integrated circuits and are widely used components in digital circuits. These are also a part of larger integrated circuits. These are a specific type of sequential circuit like registers or the value of the flip-flops serving as the output.