What are the internal forces at the right side of point C where an external force (4 kN) is acting on in the simply supported beam shown below? M = 2 kN·m 4 kN 2 m 2 m 2 m 4 kN 6kN·m C CIND 1 kN Vc Mc OV = 1 kN, M == 6kN⚫m C C OV1 kN, M =6kN⚫m C C V = 3 kN, M == C C · 6 kN • • m OV=-3kN, M=6kN •m C C B

What are the internal forces at the right side of point C where an external force (4 kN) is acting on in the simply supported beam shown below? M = 2 kN·m 4 kN 2 m 2 m 2 m 4 kN 6kN·m C CIND 1 kN Vc Mc OV = 1 kN, M == 6kN⚫m C C OV1 kN, M =6kN⚫m C C V = 3 kN, M == C C · 6 kN • • m OV=-3kN, M=6kN •m C C B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

points A, B and D, respectively, as shown in the figure. A uniformly distributed loac of 4 kN/m acting vertically downwards extends for a length of 4 m between point A and C. Page 3 of 6 5 kN 10 kN 4 kN/m A 2 m 2 m 1 m 2 m 30 kN Figure Q2: A cantilever beam 2.1. Calculate the magnitudes and directions of the support reaction force RE and bending moment ME and at point E. 2.2. Establish the equations of shear forces (SF) and bending moments (BM) for each span of the beam. 2.3. On the basis of the established equations for SF and BM for the cantilever beam, construct the shear force and bending moment diagrams along the entire span of the beam. 2.4. Determine the magnitude and position of the maximum bending moment acting on the beam. 2.5. Calculate and show the positions of the points of contra-flexure (PCE)
6. As shows in the picture, the two ends of shaft are fixed, the torsion stiffness GI, is constant. Request the support moment at the two ends of shaft (A and B). effo B (b)
Q2(a) An I-beam with varying distributed loadings is shown in Figure 2(a). Solve for the equivalent resultant force, and replace the distributed loading by specifying the resultant force location measured from point O. i. Sketch the free body diagram of the relocated resultant force from point O and the support reactions at O and B. ii. iii. Solve for the reaction forces at support A and B. 200 N/m 4 m 3 m Figure Q2(a) (b) Figure Q2(b) shows three smooth journal bearings at A, B, and C with four external loads. i. Sketch the FBD for all forces and reactions along rod ABC. ii. Solve the support reactions at all journal bearings collar A, B, and C. 900 N 600 N 450 N 0.6 m 0.9 m 0.6 m B. 0.9 m 0.9 m 0.9 m y 500 N 0.9 m Figure Q2(b)
do fast ,No much explanation need. Just need to verify the answer
Wo h B b Figure-3 A simply supported beam is subjected to loading as shown in Figure-3. If wo=14 kN/m, L=5m, b=82 mm, h=104 mm; Determine the reaction force (kN) at A. Determine the reaction force (kN) at B. Determine the magnitude of the absolute maximum moment (kN.m). Hint: Draw the moment diagram of the beam and find the maximum moment on the diagram. Alternatively, you can calculate the bending moment equation and find the maximum moment. Determine the moment of inertia (mm*) about the horizontal axis. Determine the magnitude of the maximum normal stress (MPa) due to bending.
A sign of mass 6.2 kg is hanging from a uniform beam of mass 11.2 kg and length I as shown in the diagram below. Here e 51.3 and 51A. The beam is in cquilibrium. Calculate the vertical force at the hinge. 90 -e
please help me solve and explain
Beam with a pin support at point A,roller support at pint B and the acting forces can be seen below. Determine the internal forces and moments at the mid point of BC section. (20 Points) 6 m 12 kN/m B 3 m 6 kN
QUESTION 4 For the loaded structural beam shown in the Figure, the resultant support reaction at B is: 4 kN 7 kN 45° 30° B C. 1 m Im 15m 幸 · Beam O a. 4.46 kN Ob. 2.81 kN O c. 6.33 kN O d. 3.234 kN
- For the frame of the figure:a) Draw up the free-body diagram of the three elements that compose it, for the BCD element, set theequilibrium equations (summation of forces along the longitudinal axis "t" and the perpendicular "n", as well as thesummation of moments at point C). Note: it is not required to evaluate the reactions or the charges on the elements.b) Make a cut at the midpoint between C and D and “CALCUE” the internal loads numerically.
For the structural frame shown in figure (4), draw the axial, shear forces and bending moment diagrams for member abc. 20 kN/m 3m b 3m a ZRoller Pin 4m 4m Figure (4)