We are going to add a low pressure turbine (5-6) to the system we just analyzed. Before going into the L-P turbine, the exit steam from the first turbine (3-4) is reheated in the boiler at a constant pressure. Assume both 4 & 6 are at 100% saturated vapor state and the vapor exiting from the H-P turbine (state 4) expands to a lower pressure of 2 MPa (P4-2 MPa) before it is being reheated at a constant pressure to the state 5. Recalculate (a) the thermal efficiency of the system.

We are going to add a low pressure turbine (5-6) to the system we just analyzed. Before going into the L-P turbine, the exit steam from the first turbine (3-4) is reheated in the boiler at a constant pressure. Assume both 4 & 6 are at 100% saturated vapor state and the vapor exiting from the H-P turbine (state 4) expands to a lower pressure of 2 MPa (P4-2 MPa) before it is being reheated at a constant pressure to the state 5. Recalculate (a) the thermal efficiency of the system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3- A reaction turbine is supplied with steam at (60 bar, 600 C°). The condenser pressure is (0.07 bar). If the reheat factor can be assumed to be (1.04) and the stage efficiency is constant throughout at (80%). Calculate the steam flow required in (ton/hr) for a diagram power of (25 MW). (Ans. 75.6 ton/hr) The ctoam ntion at full load for a 12 MWV) turbine ic (1 S 6 ton /brl At balf lead the
GA: In a reaction turbine, the angles of receiving tips are 35° and of discharging tips, 20°. The blade speed is 100 m/s. Calculate the tangential force, power developed, diagram efficiency, and axial thrust of the turbine, if its steam consumption is 1 kg/min. Draw the velocity diagram on scale. B: What are the objects of using the condensers in steam plants?
Thank you
Q4// Answer A or B 201u, 4017 All What is the final part of the flue gas way of boiler furnace found to raise the temperature of water? Explain this?. Also, demonstrate briefly the water movement in power plant? B// What are the types of feedwater heaters in power plant, compare them? Explain the methods of cooling by these heaters and the ways of feeding.
The Siemans SST-400 GEO steam turbine is employed in the cycle shown above. Operational information is are shown in the table. you can assume the turbine is adiabatic and you can ignore the KE & PE terms. you can assume that the pump operation is isentropic. the surrounding temperature is 25°C based on the table information: a.Calculate the mass flow of steam [96.5kg/s] b.Find the isentropic efficiency of the turbine [0.836] c.What is the rate of entropy generated (kW/K) in the turbine? [28.26kW/K] d.Calculate the thermal efficiency of the power plant [0.199]
When a steam boiler generates saturated steam at 2.5 mpa and the condenser pressure is 20 kpa, what is the Rankine cycle efficiency?Show complete step-by-step process and solution.
5. Sketch a Rankine eycle on T-s diagram and derive the thermal efficiency for a rankine eycle from its 4 steps. Show on T-S plot and discuss what is the effect of a. Increasing superheat b. decreasing condenser pressure c. Adding friction at pump and turbine
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 o the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram i. Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. ii. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.
Example 4.5: Stem expands in a turbine from 25 bar and 300°C to a condenser pressare of 20 KPa. Evaluate the Rankine cycle efficiency. What is the efficiency if the initial tempprature of steam is 500°C instead of 300°C ? Now if the boiler pressure is increased to 60 bar maintaining the steam temperature at turbine inlet at 500°C, calculate the efficiency. Assume the condenser pressure to rmain constant in all the cases. n-25 bar
An ideal reheat turbine with one stage of reheat receives steam at 8.0 MPa, 480 o C. Reheatpressure is 0.83 MPa and exhaust pressure is 0.007 MPa. The work is 1559 kJ/kg and the thermalefficiency is 41.05%. Find the temperature of steam leaving the reheater. (3 decimal in final answer pls)
COMBUSTIONMENGINEERING PROBLEM: Rdirat www A regenerative-reheat gas turbine with intercooling between turbine stages is shown in figure. Air enters at 100 kPa, 300 K with a mass flow rate of 5.807 . The pressure ratio across the two-stage sec compressor is 10. The pressure ratio across the two-stage turbine is 10. The intercooler and reheater each operate at 300 kPa. At the inlets to the Turbine stages, the temperature is 1400 K. The temperature inlet to the second compressor stage is 300 K. The polytropic efficiency of each compressor and turbine stage is 80 %. The regenerator effectiveness is 80 %. č, = 1.005 , k = 1.4 Determine a. The Compressor work, in kg air k/ b. The Turbine work, in- kg air c. The Net cycle work, in- kg air d. The thermal efficiency, in percent e. The work ratio f. The The net power developed, in kW E- Draw the corresponding cycle diagram on the pv plane.
In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the thermal efficiency of the cycle? Show step by step and draw schematic diagram