Water with density 1000 kg/s enters a lawn sprinkler which is rotating at 500 RPM through its base at the steady rate of 1 L/s as shown. The exit area of each of the two nozzles is 30 mm^2 and the flow leaving each nozzle is in the tangential direction. The radius, r, from the axis of rotation to the centerline of each nozzle is 157 mm. The absolute velocity out of each nozzle in m/s is: Select one: a. 25.11 Nozzle exit area - 30 mm2 Control volume b. 8.45 C. 83.33 Flow out Flow out Tshaft

Water with density 1000 kg/s enters a lawn sprinkler which is rotating at 500 RPM through its base at the steady rate of 1 L/s as shown. The exit area of each of the two nozzles is 30 mm^2 and the flow leaving each nozzle is in the tangential direction. The radius, r, from the axis of rotation to the centerline of each nozzle is 157 mm. The absolute velocity out of each nozzle in m/s is: Select one: a. 25.11 Nozzle exit area - 30 mm2 Control volume b. 8.45 C. 83.33 Flow out Flow out Tshaft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A water jet pump has an area Aj = 50 cm² and a jet velocity v = 25 m/s, which entrains a secondary stream of water having a velocity vs = 3 m/s in a pipe of total area 4= 500 cm². At section 2, the water is thoroughly mixed. Assuming one-dimensional flow and neglecting wall shear, estimate the following. a. The average velocity at section 2 b. The change in pressure from plane 1 to 2, (P2-P1), assuming the pressure of the jet and secondary stream to be the same at section 1 0₂
A jet of water 50 mm in diameter strikes on a fixed plate normally with a velocity of 20 m/s. Find the force exerted on flat plate.
(3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank has a circular cross section of diameter D and the flow exit has a circular cross section of diameter Do. Do not assume that H(t) is constant. The fluid has density p and the exit is open to the atmosphere. Wall H D- Do Cable Vo (1) Determine H(t) and the exit velocity Vo(t). (2) Determine the tension in the cable as a function of time Your answers should be in terms of given parameters (D, Do, p, g) о,
Do the ODE of it
Problem 5.2 A simple air duct with a side exhaust is shown below along with the direction of the velocity vectors at each inlet or outlet. The cross-sectional area at 1 and 3 are identical, Ac1 = Ac3 = 0.5 m². The velocity at 2, V₂, makes a 20° angle with the opening in the side of the duct A₂ = 0.5 m². Measurements indicate that the flow is steady with velocities V₁ = 10 m/s and V3 = 3 m/s. Assume that air behaves like an incompressible substance under these conditions. a) Determine the ratio of the volumetric flow rate at 2 to the volumetric flow rate at 1, /. b) Determine the ratio of the velocity at 2 to the velocity at 1, V₂/V₁. 1 20° Ans: a) 0.65 ≤ / ≤ 0.81 b) 1.75 ≤ V₂/V₁₂ ≤ 2.10
A centrifugal pump impeller delivers 4000 gal/min ofwater at 20 ° C with a shaft rotation rate of 1750 r/min.Neglect losses. If r 1 =6 in, r 2 = 14 in, b 1 = b 2 =1.75 in,V t 1 = 10 ft/s, and V t 2 = 110 ft/s, compute the absolutevelocities ( a ) V 1 and ( b ) V 2 and ( c ) the horsepower required.( d ) Compare with the ideal horsepower required.
A single-stage axial flow pump with outer radius r2 = 0.240 m and inner radius r1=0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q = 0.265 m^3/s, a water density p = 1.000 x 103 kg/m^3, a rotation speed n = 2.4 x 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2, and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Looking at the following image, find all values of the velocity triangle just before the impeller inlet and just after the impeller outlet at radius r =0.09 m. impeller Figure 37.1 A propeller of an axial flow pump a₁ w1 U₁ Outlet guide vane B₁ Impeller α₂ Vw2 U₂=U₂=U
A and B are homologous pumps operating at the speed of 800rpm.Pump A has an impeller with diameter 60 cm and discharges 1.5m^3/s of water under a net head of 60m.Calculate the size of pump B, net head and the specific speed to discharge 0.9m^3/s.
draw the diagram
The airduct shown below has a slanted exit, the dimension of which is 2 inch by 3 inch. Air is flowing out of the duct at a velocity of 6 ft/s, 45° to the surface of the exit. Pressure is 1 bar (14.7 psia) and temperature is 60 °F. Please compute • Density of air at this pressure and temperature; • Mass rate-of-flow through the duct; • Momentum rate-of-flow through the duct along the direction of air flow. 3 in. Air flow 6 ft/s 2 in. Side view 45°
Two gases enter a combining tube and leave as a single mixture. . For the first gas, A₁=72in² V₁=205m/s V₁=120gal/lbm . For the other gas, A₂=48in² m2=20lbm/s P2=2kgm/m³ ● . At the exit, V3=320ft/s V2=9ft³/lbm Find the (a) velocity at section 2 in m/s, (b) mass flow rate at the exit section in kgm/s, and (c) area at the exit section in m².
Momentum Water flows through a horizontal, 180° pipe bend as is illustrated in the Fig. The flow cross‐sectional area is constant at a value of 9000 mm2. The flow velocity everywhere in the bend is 15 m/s. The pressures at the entrance and exit of the bend are 210 and 165 kPa, respectively. Calculate the horizontal (x and y) components of the anchoring force needed to hold the bend in place.