Water (p =10 kg/m³) flows through the shown horizontal pipeline. At section (1), the flow velocity and gage pressure are 6 m/s and 5 kPa, respectively. Water leaves sections (2) and (3) to the atmosphere with the same velocities (V2 =V3). The cross-sectional area is 0.15 m² for the three sections (A=A=A;=0.15 m²). Find the x and y-components of force necessary to restrain the section. 5 kPa Water (1) (2) 30° (3)

Water (p =10 kg/m³) flows through the shown horizontal pipeline. At section (1), the flow velocity and gage pressure are 6 m/s and 5 kPa, respectively. Water leaves sections (2) and (3) to the atmosphere with the same velocities (V2 =V3). The cross-sectional area is 0.15 m² for the three sections (A=A=A;=0.15 m²). Find the x and y-components of force necessary to restrain the section. 5 kPa Water (1) (2) 30° (3)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the diameter of steel pipe needed to deliver water (20°C) at a rate of 2 cu. m/s from a reservoir with water surface elevation of 60 m to a reservoir 200 m away with a water surface elevation of 30 m. Assume a squared edge inlet and outlet (k = 1) and no bends in the pipe. Further assume there are two open gate valves in the pipe (k=0.2).
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend is installed in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the x and y for components of the thrust block to hold the pipe bend. Horizontal Thrust block 30° 50° Open end Ø80 mm Ø 160 mm Figure 3 Cs Scanned with CamScanner Vertical
In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) = 40 m/s, velocity of flow at the outlet of the pipe (V2) = 20 m/s and the acceleration due to gravity is assumed to be 10 m/s2, then the loss of head due to sudden enlargement of pipe is: a. 18 m of water b. 40 m of water c. 15 m of water d. 20 m of water
Water piping A circular pipe used to discharge water from one reservoir to another reservoir. The fluid is assumed to be viscous. Determine the flow rate and the pressure as A ( consider all head losses). Diameter of the pipe D=6 cm, roughness heigh of the pipe k=0,15cm, minor loss coefficients K1=0,5, K2=K3=K4+K5=1, K6=10, K7=1, kinematic viscosity of water =10^-6 m2/s
Props of fluids.
Q4: A tank of water empties by gravity through a horizontal pipe into another tank in figure (1) .There is a sudden enlargement in the pipe as shown.At a certain time the difference in levels is 3m.Each pipe is 5m long and has a friction coefficient Cf-0.007 The inlet loss constant is K=0.5 and bore diameter in point A 20mm ,and bore diameter in point B 60mm.Calculate this point. the volume flow rate at Calculate the volume flow rate at this point. (1) 20 mm bore diameter 3 m 60 mm bore diameter (2)
Note:hand written solution should be avoided.
The circular water pipes shown in the sketch are flowing full. The velocity of flow (in m/s) in the branch pipe "R" is PI V = 6m/s, dia = 4m - = V = ? R Q V = 5m/s dia = 2m