Water is being pumped from Lake 1 to Lake 2 by a 15.4 horsepower pump with an efficiency of 65%. If the head loss in the system is 15.0 ft, determine the flowrate into Lake 2 (ft3/s) Lake 1 1x 8-in. inside- diameter pipe Pump 30.0 ft Lake 2 38.5 ft

Water is being pumped from Lake 1 to Lake 2 by a 15.4 horsepower pump with an efficiency of 65%. If the head loss in the system is 15.0 ft, determine the flowrate into Lake 2 (ft3/s) Lake 1 1x 8-in. inside- diameter pipe Pump 30.0 ft Lake 2 38.5 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Reservoir A (Elevation 300m) supplies water to reservoir B (Elevation 180m) thru a 450 mm ductile iron pipe. A turbine is installed in the same level with Reservoir B. The total system flow is 350 gpm determine the the output power in Hp if the turbine is 75% efficient and the total headloss of the system is 3.5m.
Water 2. In this system, d = 6 in., D = 6 ft, and =z2 = 12 ft. The water in the system is 13 cfs. machine a pump or a turbine? pressures at points A and B? losses. Pump 1. The discharge in the siphon is 2.80 cfs, D = 10 in., L1 = 3 ft, and L2 = 3 ft. Determine the head loss between the reservoir surface and point C. Determine the pressure at point B if three-quarters of the head loss (as found above) occurs between the reservoir surface and point B. 1 m REVIEW Home Work (1) Energy Equation Water T = 10ºC REPPER Water Same elevation Machine Elevation = 40 m -Elevation = 20 m Elevation 10 m 300 m + -300 m- 4. Assume that the head loss in the pipe is given by hL = 0.014(L/D)(V2/2g), where L is the length of pipe and AZ₂ AFL B Elevation 100 m L = 100 m D = 60 cm Water T= 10°C 3. A water discharge of 10 m3/s is to flow through this horizontal pipe, which is 1 m in diameter. If the head loss is given as 7V2/2g (V is velocity in the pipe), how much power will have to be supplied to the flow…
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
4.32 ft 24.5 ft 7.47 ft O Air at 29.4 psig pump A pump delivers water from a lake into a 6 ft diameter by 10 foot tall sealed pressurized tank through 4 inch pipes using a 4.0 horsepower pump with an efficiency of 62%. If the head loss through the system is 6.42 ft, determine the delivery rate (m3/s) of water to the tank, for the tank level and pump pressure shown in the drawing.
Question 2) The centrifugal pump in the figure is in his preference Passing water at 25°C from the tank through the 1.22 m exchange store pumping. Inner diameter of the suction channel is 101.6 mm, in total it is 0.0306 and its length is 3.2 m. It the local coefficients of the user in the pipe are 7.4. If the pump works at a flow rate of 109 m3/h ENPY=1.52 is m. Does the pump work without cavitation at this flow? Show the calculation. For water, p=997 kg/m3 and Pb=3.169 kPa. Piping system at the entrance (Suction pipe) pump 22 Patm=101.3 kPa and 0.2=1.05. van
2. A pipe 120 mm bore diameter carries water with a head of 3 m. The pipe descends 12 m in altitude and reduces to 80 mm bore diameter. The pressure head at this point is 13 m. The density is 1000 kg/m3. Assuming no losses, determine i. The velocity in the small pipe (7 m/s) ii. The volume flow rate. (35 dm³/s)
Solve using the water power formula = (Q*h)/102
5. Calculate the power delivered by the oil to the fluid motor shown in the following figure if the volume flow rate is 0.25 m3/s. There is an energy loss of 1.4 N.m/N in the piping system. If the motor has an efficiency of 75 percent, calculate the power output. ( Oil (sg=0.86) Motor Flow Diameter 15 cm- 10 m
need help. Asap
find the diameter through circular duct if the flow rate (0.98 m3/s) and velocity(5m/s) Fulleen Snip 280 mm 490 mm 560 mm 750 mm 820 mm
Calculate the Flow Rate of water at 5°C through the system below. Q = Flow 3.4 m 700 kPa 30 mm diameter DN 65 mm Schedule 40 Pipe
Patrick is building a cabin on a hillside and has proposed the water system shown below. The distribution tank in the cabin maintains a pressure of 27 psig above the water. There is an energy loss of 14.6 lb*ft/lb in the piping. When the pump is delivering 37 gal/min of water, compute the horsepower delivered by the pump to the water. PA = Submit Question Distribution tank 4 ft Flow hp 214 ft Pump 1 ft