Water flows through the pipe section shown. At the inlet the water velocity is 3.7 m/s and the mass flow rate is 17 kg/s. At the outlet the water velocity is 7.3 m/s. Determine the total nett force (Fbolts shown) exerted on the bolts holding the pipe together (not the force of each individual bolt). Provide answers to 1 decimal place and Sl units are required Inlet diameter D System - fluid flow through bolt-connected pipe Outlet diameter d Fluid in Fluid out BACK VIEW FRONT VIEW SIDE VIEW Free body diagram F holts Min' Mout

Water flows through the pipe section shown. At the inlet the water velocity is 3.7 m/s and the mass flow rate is 17 kg/s. At the outlet the water velocity is 7.3 m/s. Determine the total nett force (Fbolts shown) exerted on the bolts holding the pipe together (not the force of each individual bolt). Provide answers to 1 decimal place and Sl units are required Inlet diameter D System - fluid flow through bolt-connected pipe Outlet diameter d Fluid in Fluid out BACK VIEW FRONT VIEW SIDE VIEW Free body diagram F holts Min' Mout

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A B 3. Pipe no. Diameter (mm) Length (m) Friction factor Q (I/s) 1 75 120 0.018 15 l/s 2 100 150 0.020 125 180 0.022 Compute Q2, Q3 and total Q
3. A plate is held against a horizontal water jet in the horizontal plane as shown. The jet has a diameter of 30 mm and an unknown velocity. A force of 200 N is required to hold the plate in the position. Determine the velocity of flow of the jet just before it hits the plate. What is the discharge? OP W F5 F6 F7 F8 DELL F9 E 200 N F10 F12 PrtScn SysRq Scroll Lock Pause Break
pipe 310 m Water is flowing in a straight concrete lining centrifugally spun pipe as shown in the figure problem 12. The difference between the two gauge readings is 185 kPa. The flow rate is designed to be 30 liter/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter. (Ans.: 228 mm, 123 mm) TABLE 5.1: Pipe Characteristies Pipe Hazen-William* Roughness e (mm) 0.15 C 140 Asbestos Cement (AC) – all ages Cast Iron, Ductile Iron - new 0.3 130 10 years old - 20 years old 1.5 3.0 100 90 Cast Iron coated – good condition all ages Welded steel - uncoated - new 0.3 135 125 100 100 - old 0.6 1.5 Coal tar enamel coated steel – new Concrete lining centrifugal spun – all ages Galvanized Iron (GI), Mild Steel (MS) HDPE, UPVC, Polyethylene Wrought Iron Copper, Brass *The Malaysian Water Association - MWA (Design Guidelines for Water Supply Systems) 0.15 0.15 140 0.3 130 0.015 155 0.045 ND 0.0015 ND ND = No Data
Q2: An otl of viscosity Co.15 pas) and specific gravity 0.9 is flows Throngh 1.Find The slope of The Pipe That will canse The Pressure to be constantalong The pipes entire length? an inclined (300mm) diameter Pipe. Q= 0.005m3/sec 3oomm Dia. Zz datum 2. check if The Rlow is laminarRlow?
Consider the tripod shown in (Figure 1). Figure 0.5m 25m < 1 af 1 Part A Determine the magnitude of the moment of the force F= {501-23 j-80k) N about the base line BC of the tripod. Express your answer three significant figures and include the appropriate units. ▸ View Available Hint(s) MBC = Submit Provide Feedback OL μA Value O Units ?
A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a diameter of 1/2 in. The bolt connecting the top yoke and the bottom strap has a diameter of 5/8 in. The bottom strap is 3/16 in. thick by 1.75 in. wide by 36 in. long. The weight of the pipe is 2,000 lb. Determine the following: (a) the normal stress in the hanger rod, (b) the shear stress in the bolt(c) the bearing stress in the bottom strap. Please explain the solution
Oil sg = 0.84 flowing through a pipe %3D has a total heal loss 3ft from pt.1 to pt.2. As the figure is shown, find the pressure (in pound/ squarefeet) at pt.2. Point 1 D, -6 -65 Q- 2.08 da 10.20 Q-2.06 ch Point 2 D,-9m 2-7 4.00 Reference datum Pig. 8-25
P Assignment #2.pdf File | C:/Users/user/Downloads/Fluid%20Mechanics/Assignment%20%232.pdf A 50 °C of liquid water is flowing into and discharging from a pipe U-section as shown in Figure 1. At flange C, the gage pressure is 355 kPa. Assuming frictionless, incompressible, one dimensional flow of water, determine; a) the velocity and pressure for each flange b) the resultant force required to hold the bend in place and the direction in which it acts. 120 mm 50 mm A 45 kg/s 58° 60 mm B Figure 1 2:39 PM O Type here to search a 4) * ENG 30/5/2021 +
FLUID FLOW IN PIPES I. Proving. SHOW THAT 21 5.v=R3S2 → hf n 10.29n²LQ² D16/3
H.W6: 1- discuss the stability and determinacy of the following structure 2- Draw N, V and M diagrams for part BCD A 2m F water 4m G 2m B water HCI E 2m 2m + 2m 12m2r 2m D 4m
A homogeneous rectangular gate AB 6.1 ft wide and 10 ft long. Friction in the hinge is negligible. Find force acted on surface AB? L = 5.06 ft 60 A water L B hinge Answer:
- FLUID FLOW IN PIPES I. Proving. SHOW THAT 3. hf 4. hf: fLv² 2Dg fLv² 2Dg 0.0826fLQ² D5 128μLQ πρgD4