Water flows through a sand filter. The soil mass's cross-sectional area and length are 2900 cm² and 1.65 cm, respectively. The coefficient of permeability of the sand filter is 0.0034 cm/s and the head difference between the inflow and outflow is 0.35 cm. Required Determine the flow rate of of water through the sand in L/min, to the nearest 1000th. Your Answer:

Water flows through a sand filter. The soil mass's cross-sectional area and length are 2900 cm² and 1.65 cm, respectively. The coefficient of permeability of the sand filter is 0.0034 cm/s and the head difference between the inflow and outflow is 0.35 cm. Required Determine the flow rate of of water through the sand in L/min, to the nearest 1000th. Your Answer:

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.11P

See similar textbooks

Similar questions

Water flows through a sand filter as shown on the figure. The soil has a cross sectional areaof 0.25 m2. 1. Compute the coefficient of permeability of the sand filter in cm/s. 2.Compute the flow of water through the soil in liters/sec. 3. Compute the interstitial velocity if the soil has a void ratio of 0.71 in meters per minute.
ll Ooredoo ? 2:38 PM O 100% Annotation 20... 山 A soil sample was collected near the Quriyat dam got the following properties: Coefficient of permeability k = 2.5x 105 m/sec, cross-sectional area = 45 cm?. A quantity of water 650 mL passed down for 15 minutes under an effective constant head of 450 mm. On oven drying, the test specimen has a mass of 500 g. Take Gs = 2.65, calculate a. Length of the soil sample in mm. b. Seepage velocity. Paragraph I Not allowed to type here
Determine the coefficient of permeability in mm/s from the following data:Length of sand sample = 25 cm;Area of cross section of the sample = 30 cm2; Head of water = 40 cm; Discharge = 200 ml in 110 s a.0.3788 b.0.750 c.0.106 d.1.23 x 10^(-2)
Three soil samples in a permeameter overlie one another with their characteristics listed below. Layer Hydraulic Conductivity, ft/day Length of aquifer, ft 1 10 5 2 0.20 3 0.030 12 a. Determine the equivalent hydraulic conductivity, in ft/day, if the flow is perpendicular to the stratification. b. If a falling head test is used, calculate the time required, in seconds, for the head to drop from 65 to 54 ft. The cross-sectional area of the permeameter and the standpipe are 300 square feet and 30 square feet respectively.
The SQUARE base permeameter (seen from above), has three soil layers arranged vertically as shown in the image. L is: 70cm, the difference of head h is: 105 cm. The coefficient of permeability of soil 1 K1 is 0.065 cm/sec, soil 2 K2 is 0.0030 cm/sec and soil 3 K3 is the 0.0095 Calculate the amount of water collected in a time of 10 minutes.
Problem 4. A sample of sand is tested in a constant head permeameter. The sample diameter is 50 mm and its length is 120 mm. Under an applied head of 60 cm, 113 cm³ flows through the sample in 5 minutes. The Mof the sample is 385 grams. Calculate: a. the Darcy coefficient of permeability (k) b. the discharge velocity (v) c. the seepage velocity (v₁)
The hydraulic conductivity of a sand at a void ratio of 0.62 is0.03 cm/sec. Estimate its hydraulic conductivity at a void ratioof 0.48.
The figure below shows layers of soil in a tube that is 100 mm x 100 mm in cross section. Water is supplied to maintain a constant head difference of 400 mm across the sample. The hydraulic conductivities of the soils in the direction of flow through them are as follows: ст k `sec' soil Porosity, n A 1 x 10-2 25% 3х 10-3 32% C 4.9 x 10-4 22% a.) Calculate the equivalent k in cm/sec.
Figure below shows layers of soil in a tube that is 100mm x 100mm in cross section. Water is supplied at a constant head difference of 400 mm across the sample. The hydraulic conductivities of the soils in the direction of flow through them are as follows. Soil A k (cm/sec) 1X10-2 Porosity, n (%) 25 B 3X10-3 32 C 4.9X10-4 22 Page 1 of 4 a. Calculate the equivalent k in cm/sec. b. Calculate the rate of water supply in cm^3/hr c. Calculate the seepage velocity through soil C in m/sec. 400 ha he А в с 150 150 200 mm mm mm
3. Figure shows layers of soil in a tube that is 100 mm x 100 mm in cross section. After is supplied to maintain a constant head difference of 400 mm across the sample. The hydraulic conductivities of the soils in the direction of flow through them are listed below. Calculate the equivalent k in cm/sec and the rate of water supply in cm³/hr. Soil k (cm/sec) A 1x10-2 3x103 4.9x104 Water supply Constant head difference - 400 mm
The soil sample presented in Figure below is under constant head permeability test. The soil is consist of a silty sand (SM) with k = 5×10-3cm/s and specific gravity of 2.70. The soil is fully saturated and its moisture content is determined to be 18.5%. Determine the time required for the plug of colored water to pass through the soil (i.e., from when the leading edge first enters the soil to when it begins to exit). Use seepage velocity for your calculation.
Figure below shows layers of soil in a tube that is 100mm x 100mm in cross section. Water is supplied at a constant head difference of 400 mm across the sample. The hydraulic conductivities of the soils in the direction of flow through them are as follows. Porosity, n (%) 25 32 22 Soil A k (cm/sec) 1X10-2 3X10-3 4.9X10-4 a. Calculate the equivalent k in cm/sec. b. Calculate the rate of water supply in cm^3/hr c. Calculate the seepage velocity through soil C in m/sec. 400 he A в 150 150 | 200 mm mm mm