Water flows inside a pipe and exits to the atmosphere at an average velocity of 3 m/s as shown. The mass of the pipe filled with water in the inclined section is 13 kg per meter length of the pipe. The inclination angle 0 10 a) Calculate the reaction force needed to hold the pipe in place. b) Calculate the bending moment acting on the base of the pipe at point A. c) Determine how much is it required to extend the length of the inclined pipe so that the bending moment at point A will be zero. 3 m/s 2 m -10 cm

Water flows inside a pipe and exits to the atmosphere at an average velocity of 3 m/s as shown. The mass of the pipe filled with water in the inclined section is 13 kg per meter length of the pipe. The inclination angle 0 10 a) Calculate the reaction force needed to hold the pipe in place. b) Calculate the bending moment acting on the base of the pipe at point A. c) Determine how much is it required to extend the length of the inclined pipe so that the bending moment at point A will be zero. 3 m/s 2 m -10 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An overhanging beam AB is loaded as shown in the figure and is resting on roller support at A and hinge support at B. Determine the reactions developed at the supports. 60 kN/m 20 kN 30 kN 10 kN/m A B TTTITT 2m 6m 2m 2m
Solve the reaction of the following beam structure. Show your solution. 900 Ib/ft 5.) 2.5 kips 400 Ib/ft 10 ft 18 ft
Calculate the resultant support reaction at A. C 1.5 in. 60° 8 ft 2 kip/ft
Solve the bending stress about the y-axis at points A and B. Indicate if the stress is in tension or compression. 200kN m B 200mm ▶44 15mm 200mm A 400mm 20mm
A fixed crane with a mass of 2000 kg uses a stainless steel cable (Yield Strength =210 MPa) to lift a 2400 kg mass. The center of the gravity of the crane is located at G and ean be used to model the weight of the crane at a single point. • Determine the reactions at A and B • Determine the minimum diameter that the cable should be to lift a 2400 kg object for the given erane using a factor of safety equal to 2.5. 2400 kg 1.5 m B +2 m- 4 m-
The masses of the frictionless cylinders A and B in FIG JWU are 2.0 kg and 1.0 kg, respectively. The smallest value of the force P that will lift cylinder A off the horizontal surface is 55.5 N. 24. Calculate the radius R of the cylinder B.a. 12.5 mm b. 15 mm c. 10 mm d. 16 mm 25. Determine the reaction of the wall at cylinder A.a. 58.87 N b. 29.43 N c. 55.5 N d. 9.81 N
Problem 2. For the beam shown, choose the spring force as the redundant reaction. The modulus is E = 30 x 106 psi. Determine: a) The support reaction at the base of the spring, b) the rotation of the beam at the left support. 5000 lb/in. R₁ 500 lb/ft -20 .2 m 2² 4"
The cross-sectional area of each clamp forming a fixed-supported cage system from points C and D shown in the figure below is 300 mm² and a modulus of elasticity is 105 GPa. A single force P-90 KN acts on the Kafcs system from point A as shown in the figure. Determine the vertical displacement at point A using the work-energy method. 2 m B P 1.5m
2. Calculate the support reaction for the beam shown. 60 kN A 2m² 'm 20 kN/m m 위
A rectangular plate 1 m wide by 2 m long is immersed in water of density 1000 kg/m3. The shorter side is parallel to the water surface and 0.5 m below it. The longer side is inclined at 60o to the vertical. Calculate the magnitude, direction and location of the force acting on one side of the plate due to water pressure. A bridge across a river has an elevation as shown. When the river is in flood, the upstream water surface is level with the road surface and the downstream level is 5 m below it. Assuming the pressure distribution to be hydrostatic, calculate a) the horizontal thrust upon the bridge and b) the overturning moment acting upon it. Determine the force due to hydrostatic pressure, acting on the hinge of the gate. The rectangular gate AB is 3.05 m x 1.22 m in dimension and its pin connected at the point B. If the surface on which the gate rests at A is frictionless, what is the reaction at A? A vertical gate 20m x 5m is hinged in a stream as…
0.589 Problem 3 - 105 has a ne top of the In the figure shown, the 8-ft-diameter cylinder, 3 feet long weighs 550 lbs and rests on the bottom of a tank that is 3 feet long. Water and oil are poured into the left-and right-hand of the tank to depths 2 feet and 4 feet, respectively. Determine the magnitudes of the horizontal and vertical components of the force that will keep the cylinder touching the tank at A. Ans: Fy= 749 lb -> Fy 2,134 lbs v 752 KN 230 kN r-4 f 4 ft 2 ft Water Oil, s0.75
Q2. Determine all forces acting on body A for the system shown in figure 2. Body A weighs 200 N and the cylinder B weighs 500 N. assume all the contact surfaces are smooth. 24 ring Cable 7 A r= 0.5 m 30 0.5 m B 2 m 1m 1 m 30°