Water at 80 oF flows through a 0.21 ft diameter and 50 ft long cast-iron pipe at 53 ft/min. A.Determine the Fanning friction factor for the system B.Calculate the pressure drop in the system

Q: Select a proper schedule of pipe for each of the following conditions: FOR SET B: Steam at at 900…

A: Given: Let us consider the given data, d=10 inP=900 psiaT=900°F To find: Proper schedule of pipe.

Q: Compute the Cross sectional area of Pipe Discahrge=0.8 m3/s Velocity=2 m/s

A:

Q: Compute energy loss that would occur as 27 gal / min of water flows from a tank into a steel tube…

A:

Q: A horizontal pipe with a diameter of 350 mm discharges water at the rate of 12 m2/ min and has a…

A:

Q: 4. Calculate the friction factor and head loss hi (m) for 177.2 feet of ½ inch type L copper tube…

A: As per the guidelines I am able to answer first question only. So please repost the question number…

Q: A pump is to be placed at the beginning of a 30 m long piping system consisting of 1-1/2 inch…

A: Release head differs with pull tank level. The response is yes. Assuming you bring down the pull…

Q: Compute the resulting pressure in kPa after a "real" diffuser in which the energy loss due to sudden…

A:

Q: Acetone at 77degrees flows around the tubes and inside the rectangular passage shown in the figure…

A:

Q: Calculate the volume flow rate of oil from the nozzle and the pressure at point B and D.

A:

Q: Calculatethe energy loss for water flowing at 8m/sthrough a standard tee fitting withan18-in ductile…

A: GIVEN:Water flow rate, Q=8m3/sDiameter of pipe=0.4572mFrom data book, MACHINE DESIGN DATABOOK BY VB…

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A:

Q: 4. Oil of s.g.=0.85 is flowing in a pipe under the conditions shown in Fig. III. If the total head…

A:

Q: A 4 standard type L copper tube is 200 ft long. It is to convey propyl alcohol. The available pump…

A: 4 in standard pipe- Type L copper tubefluid used: Propyl alcohol

Q: A ventilation duct in a large industrial warehouse measures 1067 mm * 1524 mm. Compute the circular…

A:

Q: Determine the discharge for laminar flow

A: Given: pipe diameter d=0.04 m centre line velocity  =1.5 m /s I;e  centre line velocity or maximum…

Q: In Figure 7, oil with a specific gravity (s.g.) of 0.852 is to be forced from Tank A to Reservoir B…

A: Given: The specific gravity of oil, SG1 = 0.852 The total length of pipe, L = 38 m The diameter of…

Q: Fuel oil is flowing in a 4-in Sch maximum rate for which the flow is laminar. If the oil has a…

A: The head loss in the pipe can be calculated using the formula given below as- hf=32μuLρgd2 where, u…

Q: Determine the maximum allowable volume flow rate in L/min that can be carried through a standard…

A: To find-: The maximum allowable volume flow rate in Lmin. Given-: The outside diameter is D=1.25 in.…

Q: A 25% Calcium Chloride brine is to be pumped through a line at 250 gpm at a temp. of 0 deg. If the…

A: Given that, Flow rate of chloride, Q=250 gpm,Pressure drop inside pipe, ∆P=0.006 lb·force/in2-ft…

Q: Fuel oil (sg=0.94) is being delivered to a furnance at a rate of 60 gal/min through a 1 1/2in…

A:

Q: The velocity of the liquid flowing through the rusty iron pipe having a 150 mm diameter is 2.5 m/s.…

A:

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: The power required by the pump can be calculated using the formula given below- P=ρgQhm where, g is…

Q: The head loss of a 174 m length of tube having a diameter of 65 mm is 41 m. Oil flows through the…

A: The friction factor. Given: The length of the pipe is L=174 m. The diameter of the tube is D=65…

Q: mass flow rate. 6.31 A liquid refrigerant (sg 1.08) is flowing at a weight flow rate of 28 3 N/h.…

A: First we have calculated the value of density of refrigerant, density of refrigerant is equal to…

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A:

Q: A vertical cylindrical gravity settler needs to be designed. A flow of 30 m3 /hr of mixture of fluid…

A: The notion of conservation of energy may be used to derive Bernoulli's principle. The total of all…

Q: IS flowin pipe at average velocity 6f m/S. Assun TIOW IS laminar, calculate the kinetic energy…

A: Kinetic energy correction factor = Kinetic energy per second based on actual velocityKinetic energy…

Q: flow is lamin

A: given: value of reynold number for fluid flow in pipe and flow is laminar?

Q: INDUSTRIAL PLANT ENGINEERING Select a proper schedule of pipe for each of the following conditions:…

A: Given Datad=10inP=900psiaT=900F

Q: in a given setup, distilled water at 75 degree f has been found to be transported through a one and…

A:

Q: A pitot tube with dia of 3cm is installed in a pipe with ID150 mm. Water flows through the pipe, and…

A:

Q: Air at a pressure of 120 psig and a temp of 50 deg F is flowing at a rate of 500 lbs/ hr through a…

A:

Q: The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the…

A:

Q: ompute the stress in Mpa in a 90 cm pipe with a wall thickness of 9.50 mm if water fills it under a

A: Givend=90cm=0.90mt=9.50mm=0.00950mPressure in pipe P=70m of water…

Q: Calculate the friction factor for atmospheric air at 80°F ( = 0.0735 Ibm/ft³,

A:

Q: ater is being discharged from a very large reservoir via the piping system shown below. piping…

A:

Q: Calculate the resistance coefficient K for a check valve swing type placed in a 6 inch schedule 40…

A: