Water at 40°C flows horizontally through a constriction similar to that in Fig. S5.9 when the atmospheric pressure is 715 mmig. The gage reading is 35 kPa, d, -0.5 m, and d, -0.15 m. Neglecting head loss, find the flow rate at which cavitation begins. 10 psi Throat 1Rde Table A.I at 40°C: Y- 9.731 kN/m', an da

Water at 40°C flows horizontally through a constriction similar to that in Fig. S5.9 when the atmospheric pressure is 715 mmig. The gage reading is 35 kPa, d, -0.5 m, and d, -0.15 m. Neglecting head loss, find the flow rate at which cavitation begins. 10 psi Throat 1Rde Table A.I at 40°C: Y- 9.731 kN/m', an da

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 20 ° C flows steadily through the piping junction inFig. P3.32, entering section 1 at 20 gal/min. The averagevelocity at section 2 is 2.5 m/s. A portion of the flow isdiverted through the showerhead, which contains 100 holesof 1-mm diameter. Assuming uniform shower flow, estimatethe exit velocity from the showerhead jets.
Question 2 //25 Q (a) In figure below the flowing fluid is Helium at 20°C. D2 =6 cm D1=10 cm Neglect losses. If pl = 1400 kPa and the manometer fluid is Meriam red oil (SG = 0.827), estimate (a) p2 and (b) the gas flow rate in m/s. R for Helium is R= 2.0769 kJ/kg/K. 0,827 1000 20+273= 293 1400 = 230 2,0769.298 Hel BT 8 cm Heliom contr 1900 - (9,81/0) 8,27 -2,30) = 932=G Q=AV,9 Q= %3D
(C./For fig shown if water flow rate is 60 lits, Find (h) Note that Density: Pwater= 1 kg/m Pair = 1 kg/m' D = 5 00mm air water 0.5 m water 25cm tat
A horizontal 7.5cm diameter sharp-edged orifice with Cc= 0.063 and Cv=0.98 is under a head of 2.30m of water (surface is atmospheric) Find the jet's diameter 1.0m above the orifice. Neglect the friction.
P.4.12 Oil of density 950 kg/m and viscosity 102 Ns/m² is to be pumped 10 km through a pipeline and the pressure drop must not exceed 2x10S N/m. What is the minimum diameter of pipe, which will be suitable, if a flowrate of 50 ton/h is to be maintained? Assume the pipe wall to be smooth. Use either a pipe friction chart or the Blasius equation f= 0.079/ Re4. Ans. d = 0.193 m D412
20 long tons of ice per 12 hrs at -15 °C were produced from steam at 190 °C. If there is no miscellaneous losses. How many TR are required? (Use 2257 and 334 as your reference values for the latent heats and 4.187 for the value of specific heat of water).
Two water tanks, each with base area of 1 ft2, are connectedby a 0.5-in-diameter long-radius nozzle as in Fig. .If h = 1 ft as shown for t = 0, estimate the time for h(t) todrop to 0.25 ft.
SAE 50W oil at 20 °C flows from one tank to anotherthrough a tube 160 cm long and 5 cm in diameter. Estimatethe flow rate in m3/hr if z1 = 2 m and z2= 0.8 m.
A) A 0.4 m diameter fan running at 970 rev min' is tested when the air temperature is 10 °C and the barometric pressure is 772 mm Hg and the volume flow rate Q=0.7 m s. Find the corresponding volume flow of a geometrically similar fan of 1 m diameter, running at 500 rev min at same conditions. Assume that the fan efficiency is unchanged. Ja
Q4) Water at 40°C flows horizontally through a constriction similar to that in Fig. S5.9 when the atmospheric pressure is 715 mmHg. The gage reading is 35 kPa, d, =0.5 m, and d, =0.15 m. Neglecting head loss, find the flow rate at which cavitation begins. O 10 psi Throat 1 ft dia Table A.1 at 40°C: y = 9.731 kN/m³ , 3 ft dia Figure S5.9
1. Obtain Bernoulli’s equation for compressible flow considering adiabatic process. 2, Define vortex flow. Derive an expression of stream function and velocity potential function for vortex flow. 3. What is Venturi meter? Derive an expression for discharge through venturi meter. 4. What is Venturi meter? Derive an expression for discharge through venturi meter.
P3.5 Water at 20°C flows through a 5-in-diameter smooth pipe at a high Reynolds number, for which the velocity profile is approximated by u = U.(v/R)/8, where U, is the cen- terline velocity, R is the pipe radius, and y is the distance measured from the wall toward the centerline. If the cen- terline velocity is 25 ft/s, estimate the volume flow rate in gallons per minute.