Water at 20 °C is being stored in a large, insu lated tank shown below. It is being recycled to the same tank by apump at an in itial ve locity of 3 m/s through apipe with a diameter of 5.25 cm. The pump supplies 98 j/kg of fluid. The exit pipe from the pump is 3.5 cm diameter and the exit pressure is 80 kN/m? abs. If the frictional loss in the pipe system is 31.5 jkg, calcu late entrance pressure of the fluid (P1) 6.0 m 3.5 cm P2 U2 VI Pi5.25 cm Ws

Water at 20 °C is being stored in a large, insu lated tank shown below. It is being recycled to the same tank by apump at an in itial ve locity of 3 m/s through apipe with a diameter of 5.25 cm. The pump supplies 98 j/kg of fluid. The exit pipe from the pump is 3.5 cm diameter and the exit pressure is 80 kN/m? abs. If the frictional loss in the pipe system is 31.5 jkg, calcu late entrance pressure of the fluid (P1) 6.0 m 3.5 cm P2 U2 VI Pi5.25 cm Ws

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer quickly
A pump is used to raise water from open tank to another one. If the pipe diameter is 300 mm, Length is 70 m, friction factor is 0.025 and total K is 2.5, the characteristic equation is Hp%3D22.9+10.7Q-111Q Find the flow rate and the head of the pump in the following cases: 1. AZ=15 m with single pump used 2. AZ=15 m with two pumps are connected in parallel 3. AZ=25 m with two pumps are connected in series
D=6.1 mmdetermine flow rate in l/s
ANSWER ASAP PLEASE
Q1) Find: (a) inlet temperature (T1 =?), (b) mass flow rate of R-134a ((m =?), (c) exit diameter (D2 =?), (d) the rate of heat transferred to the surroundings (Qout =? ). P2 = 1MPA T, = 70°C Y2 = 70 (- Compressor W in = 100 (W) R-134a P = 500KP. Qout (sat. vapor)(1) m Y1 = 20 ( D = 0.5 (cm)
A pcton-turbine develops 5MW power at a specific spced of 15. Thc water is supplied through a pipeline from a reservoir the level of which is 300m above the nozzles. Assuming for a friction loss in the pensto ck pip eline to be 5% of the gross head. The turbine speed is rpm
I need the answer quickly
Parvinbhai
A 70% efficient water pump is use to pump water to a tank which is 30 m above, the water pump is operated at 240-V, 10-A. The pipe has 5-cm-diameter at inlet and 4-cm-diameter at outlet. Irreversible head loss of the piping system is 3 m. Determine the volume flow rate and mass flow rate of the water.
A centrifugal pump must be installed 6 m above the water level in a tank. the bomb will operate at a rate of 0.01 m³/s. The manufacturer suggests a pump with NPSHR at this flow rate of 2.5 m. Neglect friction losses, with the exception of a heat exchanger between the tube inlet and pump suction, which has a loss coefficient Cf = 15. The pipe diameter is 15 cm and the pressure of water vapor at 30°C is 4.246 kPa. Is this pump suitable for the given conditions?
In Fig. the pipe entrance is sharp-edged. If the fl ow rateis 0.004 m3/s, what power, in W, is extracted by the turbine?
I need the answer as soon as possible