Problem 5. A Venturi flume with a rectangular cross-section is used to measure the flowrate from a wastewater treatment plant (Fig. 5). Given that the water depth upstream ofthe throat is h1associated with your calculation?0.8 m, calculate the corresponding flow rate. What are the assumptions1 m0.6 mFigure 5: Plan view of a Venturi flume that is used to measure the flow rate out of a wastewatertreatment plant.

Assumptions : Flow is steady irrotational flow Cd=0.98 Flow is continuos

Answered: , wastewater treatment plant (Fig. 5).…

, wastewater treatment plant (Fig. 5). Given that the v is hi = 0.8 m, calculate the corresponding flow rate. W with your calculation?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2/ If the flow rate of water through the pipe system shown in Figure shown 2 below is 0.05 (m/s) under total head loss of 0.9 (m) determine the diameter of pipe C. Assume f = 0.02 for all pipes and neglect the minor losses Pipe A 300 m, 200-mm diameter Pipe B 266 m, 160-mm diameter Pipe C 190 m Pipe D 510 m, 250-mm diameter
A municipal wastewater treatment plant processes an average flow of 5000 m³/d. A primary clarifier remove 60% of the suspended solids at average flow. The diameter of the tank is Given: Efficiency Overflow rate (m/m².d) 70 20 40 so
Problem 2: Fluid flows through a 20-mm diameter pipe, 150 m long at a Reynolds number of 1,750. Calculate the discharge if the head lost is 175 m.
Hydraulics of Sprinkler Nozzle Example// Select the diameter of the nozzle and the working pressure for a sprinkler has a discharge of (126 m2/hour)?
A flow distribution network is shown in Figure B. Use Darcy's Weisbach equation to calculate the head loss in the network. Compute the flow in the distribution network with the help of Hardy Cross method using the data shown in the figure below. Show the final flow distribution with the help of a neat sketch. All the flow rates are in liters/s. (300 Vs (50-1/s A K=10 K=20 B K=10 K=10 E F (100 /s (50 ) /s (100 I/s Figure B- Water distribution network K=20 K=10 K=20
A reservoir is to be constructed to regulate the flow of a river. The monthly inflow amounts are given below. Assuming 100% regulation, estimate the storage capacity of the reservoir. Month 0 St (106 m³) 5 N 7 D 8 J 9 F 12 M 15 A 14 M 9 J 4 J 2 A 1 S 4
Q4: A volume of water equal to 3.5x10" m'is was required to iigate a farm every 10 days. Find a discharge in m'/s if water is applied according to: 1) one day every 10 days, 2) three days every 10 days, 3) five days every 10 days, 4) 12 hrs between day and another, and 5) continuously.
Question: A sewage treatment plant for a town with 120000 population and water average temperature of 20 °C should be designed. You are asked to design a coagulation/rapid mixer and a flocculation tank with horizontal shaft paddle. The jar tests suggest average G-value of 30 (m/s)/m, minimum water residence time of 1500 seconds and GT value from 55000 to 90000. The flocculation tank should include 3 compartments with similar compartments' geometry aspects separated using baffles partitions. The width of each flocculation tank should not exceed 7 meters due to some constraints highlighted by the project's mechanical engineers about the maximum length of each shaft. Determine: 1- The volume and dimension and power requirement of the cylindrical rapid mixer 2- The flocculation tank dimension 3- Required power for each flocculation mixer 4- The paddle wheel dimension 5- Rotational speed of each mixers (Check if the speeds are acceptable) 6- Baffle size and distribution 7- Write about any…
A sedimentation basin in a water treatment plant treats a flow of 4.7 mgd and has the following dimensions: L= 141; W = 23'; Depth of water = 14. Calculate the overflow rate (OR) for the basin (in units of gallons per minute per square foot, gpm/ft?).
Example 1: A flow of water from a reservoir to a pipe of different diameters shown in Figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the energy and hydraulic grade lines. water 10m D1-300mm D2-200mm D3=100mm D4-50mm (nozzel)
mater 3
A 62 m by 80 m room in a warehouse will be protected by individual fire sprinklers spaced throughout the ceiling. Each sprinkler head covers a 4 m by 4 m area and will discharge approximately 180 liters/minute (L/min). Sprinkler heads are located in straight rows spaced at 4 m on center. For preliminary design, approximate the following: a. The minimum number of sprinkler heads requiredb. The minimum number of rows of sprinkler heads, if rows run transversely (widthwise) through the buildingc. The minimum number of rows of sprinkler heads, if rows run longitudinally (lengthwise) through the buildingd. The flow rate of the system, in L/min, based on the number of sprinkler heads