Voltage (V) [V] ● Resistor X Resistor Y A Resistor Z Current (1) [A] V=4.71 V = 2.31 V=0.61 Assume you have one resistor of each resistor shown in the graph available for use. For BOTH parts a) and b) described below: >> Determine the required resistance for the system in units of ohms [2]. >> Choose one correct resistor or resistor combination that will meet the criteria as closely as possible. (a) You want the resistor(s) to provide approximately 620 watts [W] of power when using a current of 20 amperes [A]. (b) You want the resistor(s) to provide approximately 1700 watts [W] of power when using 95 volts [V].

Voltage (V) [V] ● Resistor X Resistor Y A Resistor Z Current (1) [A] V=4.71 V = 2.31 V=0.61 Assume you have one resistor of each resistor shown in the graph available for use. For BOTH parts a) and b) described below: >> Determine the required resistance for the system in units of ohms [2]. >> Choose one correct resistor or resistor combination that will meet the criteria as closely as possible. (a) You want the resistor(s) to provide approximately 620 watts [W] of power when using a current of 20 amperes [A]. (b) You want the resistor(s) to provide approximately 1700 watts [W] of power when using 95 volts [V].

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
The voltage regulation can be equal to zero :when .The t and current is not too highO .The p.f. is leading p.f. for any possible current O .The p.f. is lagging p.f. for rated current O
A chopper is employed to charge a battery as shown in figure. The charging current is 5 A. The duty ratio is 0.2. The chopper output voltage is also shown in the figure. The peak to peak ripple current in the charging current is https://practicepaper.in/wp-content/uploads/GATE/EE/20031/q87.jpg
Known Vsat for LM741 ± 14V for source voltage Vs ± 15V. If Vi1 = 3 V and Vi2 = 4 V, Ri1 = Ri2 = Ro2 = 1 K Ohms. Define what is the value of Vo? how much
A PMMC instrument has internal resistance of 0.77 ko and gives full scale deflection for 35 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 79 V will be ohms. 102562.40 O 224.94 1487.14 O -326.96
For an RTD the relationship between resistance and temperature is a. proportional b. no relation c. equal d. inversely proportional
The characteristic of the UJT exhibits the following values: n = 0.575, RB1 = 10 k-ohms, Vv = 1.3 V, Iv =20mA, Ip=15UA. 125V B2 B, Determine the following: a. Determine the R82 (in kilo-ohms) of the UJT b. Determine the maximum value range of R (in kilo-ohms) that will ensure proper turn-on and turn-off of the UJT c. Determine the minimum value range of R (in kilo-ohms) that will ensure proper turn-on and turn-off of the UJT
Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?
For the voltage-divider bias network of Figure 1: a. Determine re. b. Calculate Zi and Zo. c. Find Av. d. Repeat parts (b) and (c) with ro = 25 k.
The drawback to using this equivalent circuit, however, is that it is defined for a set of operating conditions that might not match the actual operating conditions. a.pi b.hybrid-pi c.hybrid d.re
Using The Constant Voltage Drop (CVD) Model, please get V and I
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.