Void ratio e = 0.78 Water content w = 12% %3D Specific gravity G, = 2.68 %3D

Q: 3 k/ft 1. Determine the horizontal and vertical components of reaction at A,B,C. Assume the frames a...

A: We have to determine the value of shear and moment diagram and horizontal and vertical components of...

Q: PROBLEM 1 Find the normal stress of members CD and CE of the truss shown. Cross sectional area of th...

A:

Q: In a soil with a well developed Bt horizon (argillic horizon), the Bt horizon compared to the A1 hor...

A: Following is required answer : 

Q: Given the beam shown with computed reactions and a cross section. Determine the Maximum horizonta...

A: To determine the maximum horizontal shear stress in the beam.   Given,   The maximum horizontal she...

Q: Find the height of the free surface if 0.8 ft3 of water is poured into a conical tank 20 in high wit...

A:

Q: For the pin-jointed frame shown below: 100 kN C 4 m B 3 m 90 kN- D. 4 m 6 m- Find forces in member A...

A: Given arrangement, To find force in members AE,AB,BD

Q: Rodney drove his bike with a velocity of 30 mph, went up to 90 mph, and went down to 20 mph. What is...

A:

Q: The sketch shows a painter's scaffold in mechanical equilibrium. The person in the middle weights 25...

A:

Q: 1. 15C water is flowing through the tube shown in Figure 1 below at a rate of 0.20 m^3/s. If the pre...

A: Discharge of water in pipe, Q =0.2m3sPressure at section 1, P1 =415 KPaPressure at section 2, =P2Dia...

Q: Determine the internal loadings of the beam at point C. (Assume that the support at A is a pin and B...

A: This question is related to the Structure Analysis. In this question we solve this problem using for...

Q: 466.09 mm

A:

Q: -3% grade is connected to a +1.2% grade by means of 200 m vertical curve. The PJ station is 100+ 00 ...

A:

Q: Problem 1: a) For the design of a spillway with an economic life of 100 years the accepted risk can ...

A: We have to calculate the value of return period of design discharge and risk of that cofferdam and a...

Q: design a 2 span one way slab with length of 5m discontinous one end and continuous in the other end....

A: The shear of loads on beams supporting slabs along four edges when vertical loads are uniformly dist...

Q: mm deep and is reinforced with 4- 20 mm diam bars for tension. Using an effective depth of d = 450 m...

A: The values given in the question are as follows Width of beam(b)=280 mm Depth of beam(D)=500 mm Area...

Q: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—casto...

A: Specific gravity of linseed oil, SG1=0.938Specific gravity of castor oil, SG2=0.96The value of z = 2...

Q: The lap joint shown is fastened by 6-20mm diameter rivets. Assuming that P = 200KN, determine the sh...

A: We need to divide load by effective area to calculate stresses.

Q: Find the normal stress of members CD and CE of the truss shown. Cross sectional area of the members ...

A: ##Calculation of Normal Stresses in a member##CD , CE

Q: using the method in the analysis of beam deflections and rotations (DOUBLE INTEGRATION METHOD)  find...

A:

Q: 1. A cantilever R.C. beam is 280 mm x 500 mm deep and is reinforced with 4- 20 mm diam bars for tens...

A: Given data,The R.C beam is280×500mmThe reinforced =4-20mmd=450mmConcentrated load=10kNUniform load =...

Q: nd HORIZONTAL GRID is 2.0 m. All loads are in Newtons. All members re 900 mm2. 1) determine if the s...

A:

Q: Abe can paint the room in 15 hours, Bea can paint 50% faster than Abe, and Coe can paint twice as fa...

A: Step: 1 Paints: - It is a liquid surface coating, thin film on painted surface. Use of paint to dec...

Q: 2. (CASTIGLIANO'S THEOREM) Determine the vertical displacement of point B of the beam shown below. ...

A: Given data: E=200 GPaE=200×106 kPaI=150×106 mm4I=150×10-6 m4EI=30000 kN.m2

Q: Complete the table. Write Pre-construction, Construction, Post-construction in the second column. ...

A: Brief concept- In the construction activities, there are several stages such as Pre-construction, Co...

Q: 1 Why do steel and cable are widely bridges? used in suspension 2 Why do concrete have cracks after ...

A:

Q: complete solution and drawing. if u can please add some explanation thankyou FN = 49  MN = 101  S...

A:

Q: 4. Determine the axial forces in the members AB, AC, and BC in kN 3 m -3 m- F = 10kN

A:

Q: What is the value of strain energy stored in the given truss? (AE = 300 MN for xy, AE = 250 MN for z...

A:

Q: 3 k/ft Determine the horizontal and vertical components of reaction at A,B,C. Assume the frames are ...

A:

Q: A 5.3 m thick of soil consist of three different layers as follows: Layer 1: H1 = 1.6 m, k1 = 4.5 m...

A: Given A 5.3 m thick of soil consist of three different layers H = 5.3 m Layer 1: H1 = 1.6 m, k1 = 4....

Q: Two distributed loads act on the beam AB. If the resultant of this loads is a 2400 N-m counterclockw...

A:

Q: Draw the shear, moment, and axial force diagrams of the frame shown. Indicate the maximum shear and ...

A:

Q: What is the value of strain energy stored in the given truss? (AE = 300 MN for xy, AE = 250 MN for z...

A: Given arrangement, Axial rigidity,AE(xy)=300MN Axial rigidity,AE(zy)=250MN To find the value of str...

Q: A portion of a proposed highway extension project in the form of a compound circular curve is to be ...

A:

Q: A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working str...

A:

Q: 3 k/ft 1. Determine the horizontal and vertical components of reaction at A,B,C. Assume the frames a...

A: We have to determine the value of horizontal and vertical components of the reaction at A,B,C and dr...

Q: The maximally productive use of a property is

A: The test of maximal productivity is used to determine the first three successful tests. The property...

Q: Problem 6. In a construction project, the excavated material has a dry unit weight (Ya) of 90 pcf an...

A: Given data: Excavated material properties: γd=90 pcfw=12% Embankment material properties: γ=110 pcfw...

Q: A total station is set up over a point (2,703.521 mE, 1,481.345 mN, 1,951.418 m) with an instrument ...

A: Elevation of total station =1951.418mCoordinates of total station,(x,y) =(2703.521, 1481.345)Instrum...

Q: 3. Determine the ffg: a. resultant force of the forces shown. (in lb) b. reaction at A and (in lb) c...

A:

Q: Equation method 1) equations between loads (shear and moment) 2) diagram of shear and moment

A:

Q: A reinforced concrete beam has a width of 321mm and an effective depth of 495mm. f’c = 32MPa, fy = 4...

A:

Q: FINO Ely MID WAY BETWEN THE SUPPOS 4KN

A: We have to determine the value of EIy at the midspan of the supports or in between the supports.

Q: 1. What steps are followed in solving an indeterminate structure by consistent deformation methods?

A:

Q: From the laboratory result of a sample taken from the field, the total volume of wet sample is 1x 10...

A:

Q: SAMPLE PROBLEM #4 Determine the design strength of an ASTM A992 W14 x 132 that is part of a braced f...

A:

Q: F4-17. Draw the shear and moment diagrams for the beam. Indicate values at the supports and at the p...

A:

Q: If the bucket and its contents have a total weight of 20 lb, determine the force in the supporting c...

A: Given:- The total weight of the bucket = 20 lb The bucket is supported by the cables DA, DB, & D...

Q: compute the strenght of figure factor

A:

Q: Given data : Mass of ball=5 kg Velocity of ball =2.8 m/s Determine kinetic energy

A: