Vo A loaded railroad car is rolling at a constant velocity when it couples with a spring and dashpot bumper system. After the coupling, the motion of the car is sin16t where x and t defined by the relation x= 60e181 are expressed in mm and seconds, respectively. Determine the position, the velocity and the acceleration of the railroad car when (a) t = 0, (b) t = 0.3 s.

Vo A loaded railroad car is rolling at a constant velocity when it couples with a spring and dashpot bumper system. After the coupling, the motion of the car is sin16t where x and t defined by the relation x= 60e181 are expressed in mm and seconds, respectively. Determine the position, the velocity and the acceleration of the railroad car when (a) t = 0, (b) t = 0.3 s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The slider P can be moved inward by means of the string S as the bar OA rotates about the pivot 0. The angular position of the bar is given by 0 = 0.4 +0.12t+ 0.06t³, where 0 is in radians and t is in seconds. The position of the slider is given by r = 0.8 0.1t 0.05t2, where r is in meters and t is in seconds. Determine and sketch the velocity and acceleration of the slider at time t = 2 s. Find the angles a and ß which v and a make with the posi- tive x-axis. S 0 Problem 2/144 رفع جك
The horizontal motion of the plunger and shaft is arrested by the resistance of the attached disk which moves through the oil bath. The velocity of the plunger is v0 = 3.8 m/s in the position A where x = 0 and t = 0, and the deceleration is proportional to v so that a = -kv where k = 0.61 s-1. Find (a) the velocity when t = 5.5 s, (b) the position x when t = 5.5 s, (c) the velocity when x = 3.5 m.
The 2-1b spool slides along the smooth horizontal spiral rod, r = (20) ft, where is in radians, as shown in (Figure 1). At the instant = 90°, its angular rate of rotation is constant and equals 0 = 4 rad/s. Figure 8 = 4 rad/s 1 of 1 P Determine the horizontal tangential force P needed to cause the motion. Express your answer in pounds to three significant figures. IVE ΑΣΦ ↓↑ vec P= 6.244 Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining ? lb
In an archery test, the acceleration of the arrow decreases linearly with distances from its initial value of 14500 ft/sec² at A upon release to zero at B after a travel of 33.0 in. Calculate the maximum velocity v of the arrow. Answer: v= i BI 33.0" ft/sec
F(t) K: 3. A particle with a mass of 3 kg has velocity = 5î + 7ĵ- 3km/s. The total force acting on the particle is given by F = 3Aî - 2Aĵ + 4Ak N, where A is an unknown constant. Determine the value of A such that the x-component of the particle's velocity is 10 m/s after the force is applied for 2 seconds. Also determine the particle's velocity vector at this time.
I Suppose an autonomous surface vessel (ASV) traveling with velocity TvG/O= vi₁ begins to make a turn by adjusting the thrust of its left and right thrusters, TA and TB, respectively. The center of mass of the ASV is located at G and the ASV is symmetric about its vertical axis. The ASV also experiences a drag force that is proportional to its speed and opposes its velocity. At the instant shown, the drag force is D = -kvi₁ where k is a drag coefficient. 1. To model the mass moment of inertia, approximate the ASV as consisting of three rigid bodies: a flat plate as a center body of mass 6m and two slender rods housing the propulsion assemblies, each of mass m, at the outboard sides of the vehicle. Determine the mass moment of inertia, IG, about the vertical axis passing through the center of mass G. (Hint: Use the parallel axis theorem.) 2. At the instant shown, determine the inertial acceleration vector ac/o = axi₁ + ayi2 of the center of mass and the angular acceleration a of the…
7. The spool, which has a mass of 2 kg, slides along the smooth horizontal spiral rod, r= (0.40) m, where is in radians. If its angular rate of rotation is constant and equals = 6 rad/s, determine the horizontal tangential force P needed to cause the motion and the horizontal normal force component that the spool exerts on the rod at the instant = 45°. [Ans: P= 17.8 N and N= 59.3 N]. 8= 6 rad/s
‚A Given: The arm of the robot is extending at a constant rate ř = 1.5 m/s when r = 3 m, z = (4t2) m, and 0= (0.5 t) rad, where t is in seconds. Find: The velocity and acceleration of the grip A when t = 3 s.
1. A chain of blocks is moving upward at 3 m/s. The tension in the cable connected to the top of the chain is To = 800 N. a. What is the acceleration of the chain of blocks? b. What is the tension in the cable connecting Block C and Block D? v = 3 m/s To = 800 N mA = 21 kg mB = 25 kg mc = 20 kg mp = 18 kg mg = 17 kg mp = 15 kg a = ? TCD = ?
A hanging mass m = 84kg is released from rest and accelerates downward. The winding drum A of mass me = 60kg with an effective diameter of d, = 410mm and a radius of inertia ka = 375mm meshes with gear B. Assume ws = 5wa, with subscript a related to the winding drum and ; to gear B. B Analyse the frictionless system and calculate: The moment of Inertia of the drum Ig = maka = 8.4375 |kgm? The linear acceleration a = 3.906 m/s/8 The angular accelerations for the drum ag = 19.532 rad/s/s as well as the gear s = 97.66 rad/8/s (*) The tension in the cord F N. Assume an observation period of 4 s from the instant the system is released from rest and calculate the change of linear speed Av = m/s and linear distance the hung mass moves Ah = m (*) During the 4 8 observation, the following changes of energy with the correct sign can be computer:
For this problem, refer to the figure below. A mass M is pulled from equilibrium at r = 0 to a position I = D and is released from rest at t = 0. The spring constant k is known. There is no friction. M -D D/2 x=0 D/2 D (a) Use the initial conditions to determine explicitly the equation of motion (r(t)) of the box. (b) At which position(s) is the acceleration of the block the greatest in magnitude? (c) At what speed does the block cross point z = 0? (d) Sketch the potential energy of the block versus position. No exact values are needed - just get the overall shape down. Then, sketch the kinetic energy of the block versus position.
Bodies A and B shown in the figure are connected to each other by two ropes. Body b is located on the frictionless surface. Acismi moves down from the stop position at T=0 with a constant acceleration of 100 mm/sec2. t = 2 sec how many mm do Bodies A and B move, respectively? в A Please select one: a.200 mm down, 50 mm right b.200 mm down, 200 mm right c.200 mm down, 800 mm right d. None of them e.200 mm down, 400 mm right