View Policies Current Attempt in Progress Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 3450 mm2 and an allowable normal stress of 100 MPa. Bar (2) has a cross-sectional area of A, = 4200 mmf and an allowable normal stress of 160 MPa. Assume x = 1.9 m, x2 = 3.6 m, y, = 1.5 m, and y2= 2.4 m. Determine the laaximum load Pmax that can be supported by the structure without exxceeding either allowable normal stress. (1) Answer: Pmax kN eTextbook and Media Attempts: 0 of 1 used Submit Answer Save for Later

View Policies Current Attempt in Progress Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 3450 mm2 and an allowable normal stress of 100 MPa. Bar (2) has a cross-sectional area of A, = 4200 mmf and an allowable normal stress of 160 MPa. Assume x = 1.9 m, x2 = 3.6 m, y, = 1.5 m, and y2= 2.4 m. Determine the laaximum load Pmax that can be supported by the structure without exxceeding either allowable normal stress. (1) Answer: Pmax kN eTextbook and Media Attempts: 0 of 1 used Submit Answer Save for Later

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show that the following function may be used as an Airy stress function + = Ar + Br²y + Cxy Evaluate A, B and C for the rectangle shown in Figure Q3: (1) there are no external loads for any kind applied along KN; (2) along KL there is a uniform normal load p; (3) and along MN there is no normal load; (4) along KL, LM and MN there are shear stresses (but none along KN). Make a neat sketch of the stresses along the boundary KLMN. N M Thickness=1 p per unit length a
Find the increment inn vertical stress.
What are appropriate relations established from the calculation of maximum shear stress in a thin circular tube? 4 (b) t = (a) Tmax Tavg 3 'avg max 3 4 S Rỉ + R2R1+ R3 (c) Tmax when (R, = = 2avg - R.) (d) Tmax 3 A Rỉ + R? Here, (R, > R1) and S is shear force at the cross sectional and A is cross sectional area.
Your answer is partially correct. Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2780 psi, o,2 = -2440 psi, op3 = 0 (b) Op1 = 58 MPa, Op2 = 35 MPa, Op3 = 0 Answer: (a) Tabs max psi 1390 (b) Tabs max MPa 29
A solid 2.20 in. diameter shaft is subjected to a torque of T = 365 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 i = Tmax in-plane A i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
A bar of the rectangular cross-section is 100mm thick by 50mm broad and carries an axial compressive load of 160KN. If the line of action of the load is 12.5mm from the center of the thickness of the section along the centerline of the breadth. Determine the maximum and minimum stresses in the bar. Show complete process and solution. Given: F = W = 160KN x 1MN / 1000KN = 0.160MN B = 50mm x 1m / 1000mm = 0.50m T = 100mm x 1m / 1000mm = 0.1m X = 12.5mm x 1m / 1000mm = 0.0125m
1) Figure 1 shows an element with stresses. Angle 1 Oy Tyx Ox Txy Tyx Figure 1 Point Ax-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle.
The curved bar shown has a cross section of 30 x 30 mm. Knowing that the allowable compressive stress is 175 MPa, determine the largest allowable distance a. Take P= 4.5 kN. В. A. P P 30 mm 20 mm 20 mm 30 mm The largest allowable distance a is mm.
Cross section of each bar 350 mm2 . Find stress in bar CD
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.
A steel bar 0.75 in. in diameter has an axial load P = 13,000 lbs. a. Determine the normal stress (in MPa) on the plane through the bar that forms an angle of 30 degrees with the cross-section. b. Determine the shear stress (in MPa) on the plane through the bar that forms an angle of 30 degrees with the cross-section. c. Determine the maximum normal stress (in MPa) on the bar and d. Determine the maximum shear stress (in MPa) on the bar
A rectangular column section is as shown in the figure. 200 mm y There is a load of 200 kN, acting on the cross-section with an eccentricity of 60 mm along x-x axis as shown. Then For no tension in the given section, the eccentricity should be less than 33.33 mm Correct Option B Maximum stress for the section is 7 MPa (compression) Correct Option C Minimum stress for the section is 2 MPa (compression) D Stress at the layer parallel to weaker axis at a distance 80 mm in the direction of eccentricity is 6.1 MPa Correct Option 400 mm